Opens in a new tab

SN74LS74AN

Dual D flip-flop, edge-triggered, preset/clear, LS TTL, PDIP-14

11000

Effective Inventory

Image for reference only

Manufacturer Part:

SN74LS74AN

Package:

PDIP-14 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The SN74LS74AN is a dual positive-edge-triggered D-type flip-flop from Texas Instruments with preset, clear, and complementary outputs in a 14-pin PDIP package.

Key Specifications

Number of Flip-Flops 2 (dual)
Trigger Type Positive-edge-triggered
Logic Family LS (Low-power Schottky)
Supply Voltage 4.75V to 5.25V (5V nominal)
Max Clock Frequency 25MHz typical
Propagation Delay (CLK to Q) 25ns typical
Preset (Active Low) Yes (asynchronous, sets Q=HIGH)
Clear (Active Low) Yes (asynchronous, sets Q=LOW)
Outputs Q and Q-bar (complementary)
Output Current (IOL) 8mA
Operating Temperature 0°C to +70°C
Package PDIP-14 (19.3 x 6.35mm)

Features

  • Dual independent D flip-flops in one package
  • Positive-edge-triggered clock
  • Asynchronous preset (active low) and clear (active low)
  • Complementary Q and Q-bar outputs
  • Direct replacement for 7474 and 74LS74
  • Input clamp diodes for undershoot protection

Applications

  • Frequency division and counters
  • Data synchronization and storage
  • Shift register construction
  • One-shot and toggle circuits
  • Control state machines
Product Introduction: SN74LS74AN Product Introduction

The SN74LS74AN from Texas Instruments contains two independent positive-edge-triggered D-type flip-flops with asynchronous preset and clear inputs in a 14-pin PDIP through-hole package. Each flip-flop transfers the logic level at the D input to the Q output on the rising edge of the clock (CLK). The asynchronous preset (PRE, active low) forces Q HIGH regardless of the clock or D input. The asynchronous clear (CLR, active low) forces Q LOW regardless of the clock or D input. Both PRE and CLR override the clock, and applying both simultaneously is prohibited (Q and Q-bar would both be HIGH). The complementary outputs (Q and Q-bar) provide both true and inverted data. The device is a direct replacement for the classic 7474 and 74LS74 from any manufacturer. The AN suffix denotes the improved LS version in the PDIP-14 package.

Working Principle: SN74LS74AN Working Principle

Each D flip-flop in the SN74LS74AN captures the logic state present at its D input on the rising edge of the CLK signal. When CLK transitions from LOW to HIGH, the D input value is latched and appears at the Q output after the propagation delay (25ns typical). The Q-bar output provides the complement. If D is HIGH at the clock edge, Q goes HIGH; if D is LOW, Q goes LOW. The D input must be stable for a setup time (typically 15ns) before the clock edge and held for a hold time (typically 0ns) after the edge. The asynchronous PRE input, when pulled LOW, immediately forces Q HIGH (and Q-bar LOW) regardless of the CLK and D states. Similarly, the CLR input, when pulled LOW, forces Q LOW (and Q-bar HIGH). These asynchronous inputs are level-sensitive and override the synchronous (clocked) operation. When both PRE and CLR are HIGH (inactive), the flip-flop operates in the normal clocked mode. The flip-flop can be wired as a toggle (divide-by-2) by connecting Q-bar to D; each clock edge then toggles the output, dividing the clock frequency by two.

Pin Description: SN74LS74AN Pin Definition and Functions
Pin Name Type Description
1 1CLR Input Flip-flop 1 clear (active low, async)
2 1D Input Flip-flop 1 data input
3 1CLK Input Flip-flop 1 clock (rising edge triggered)
4 1PRE Input Flip-flop 1 preset (active low, async)
5 1Q Output Flip-flop 1 true output
6 1Q-bar Output Flip-flop 1 complement output
7 GND Power Ground
8 2Q-bar Output Flip-flop 2 complement output
9 2Q Output Flip-flop 2 true output
10 2PRE Input Flip-flop 2 preset (active low, async)
11 2CLK Input Flip-flop 2 clock (rising edge triggered)
12 2D Input Flip-flop 2 data input
13 2CLR Input Flip-flop 2 clear (active low, async)
14 VCC Power Supply (4.75V to 5.25V)
Application Scenarios: In which products and applications is SN74LS74AN used
  • Frequency Divider: Connect Q-bar to D for divide-by-2; cascade for binary counters (÷4, ÷8, etc.)
  • Data Sync: Capture asynchronous input on clock edge to synchronize to system clock domain
  • Shift Register: Chain D-to-Q connections for serial-to-parallel conversion or delay lines
  • State Machine: Q and Q-bar outputs provide current and complement states for Moore/Mealy FSM
  • One-Shot: D tied HIGH with CLK as trigger creates a pulse-width set by external clear timing
Alternative Models: What chips are recommended as replacements for SN74LS74AN
Model Manufacturer Key Difference Package Supply
74LS74N TI/Nexperia Original TTL version with 5V-only supply, typical propagation delay 10-15ns DIP-14 5V TTL
74LS74D TI/Nexperia Surface-mount SOIC version of LS with identical logic function SOIC-14 5V TTL
74HC74D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-14 2-6V CMOS
74HC74N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-14 2-6V CMOS
74HCT74D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-14 4.5-5.5V TTL-in
74HCT74N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-14 4.5-5.5V TTL-in
74AC74D TI/Nexperia Advanced CMOS with 2-6V supply and higher output drive current (24mA vs 6mA for HC) SOIC-14 2-6V CMOS
74AC74N TI/Nexperia Through-hole DIP version of AC family for prototyping and repair DIP-14 2-6V CMOS
74LVC74D TI/Nexperia Low-voltage CMOS for 1.65-3.6V modern logic with 24mA output drive and bus-hold inputs SOIC-14 1.65-3.6V CMOS
74LVC74N TI/Nexperia Through-hole DIP version of LVC family for prototyping and repair DIP-14 1.65-3.6V CMOS

The 7474 is a Dual D-Type Positive-Edge-Triggered Flip-Flop. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1