Opens in a new tab

TL431IDBVR

Precision shunt ref, 2.495V-36V adj, 0.2Ohm Zout, SOT-23-5

21849

Effective Inventory

Image for reference only

Manufacturer Part:

TL431IDBVR

Package:

SOT-23-5 (2.9 x 1.6 x 1.15 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TL431IDBVR from Texas Instruments is a precision programmable shunt voltage reference in a 5-pin SOT-23 package. With 2.495V to 36V adjustable output, 0.2Ohm typical output impedance, and 1mA to 100mA sink current capability, it replaces Zener diodes in precision power supply and reference circuits.

Key Specifications

Reference Voltage (Vref) 2.495V (typical)
Adjustable Output Range Vref to 36V
Initial Accuracy (Standard) +/-2% at 25C
Output Impedance 0.2 Ohm (typical)
Sink Current Range 1 mA to 100 mA
Reference Input Current 2 uA (typical)
Temperature Coefficient 6 mV (typical over temp)
Operating Temperature -40 to +85 C (I suffix)
Package SOT-23-5 (DBV)

Features

  • Adjustable output from Vref (2.495V) to 36V
  • Three grades: 0.5% (B), 1% (A), 2% (standard)
  • 0.2Ohm typical output impedance
  • 1mA to 100mA sink current capability
  • Low temperature drift: 6mV typical (B grade)
  • Sharp turn-on characteristic
  • Active output circuit replaces Zener diodes
  • Available in SOT-23-5, SOT-23-3, SOIC-8 packages

Applications

  • Switching power supply feedback reference
  • Adjustable voltage regulator
  • On-board regulation and voltage monitoring
  • Precision Zener diode replacement
Product Introduction: TL431IDBVR Product Introduction

The TL431IDBVR from Texas Instruments is a three-terminal adjustable precision shunt regulator in a 5-pin SOT-23 package. The I suffix indicates industrial temperature range (-40 to +85C), DBV denotes the SOT-23-5 package, and R indicates tape and reel. The standard grade provides +/-2% initial accuracy at 25C, while the A grade offers +/-1% and B grade +/-0.5%. The output voltage is set by two external resistors between Vref (approximately 2.495V) and 36V. With 0.2Ohm typical output impedance and 1mA to 100mA sink current capability, the TL431 provides a sharp turn-on characteristic that makes it an excellent replacement for Zener diodes. The active output circuitry provides much better regulation than passive Zener diodes, especially at low operating currents. This is the most widely used voltage reference IC in switching power supply feedback loops.

Working Principle: TL431IDBVR Working Principle

The TL431 operates as a precision shunt regulator through three terminal functions: (1) Reference Input (REF): The REF pin is compared against an internal 2.495V bandgap reference. When the voltage at REF exceeds Vref, the cathode current increases sharply, pulling the cathode voltage lower. This creates a high-gain feedback loop when used with external resistor dividers. (2) Cathode (CATHODE): The cathode terminal sinks current from 1mA to 100mA to regulate the output voltage. The 0.2Ohm typical dynamic impedance means the cathode voltage varies only 0.2V for a 1A change in cathode current (within the operating range). The sharp turn-on characteristic below Vref ensures the device does not draw significant current until the threshold is reached. (3) Output Voltage Setting: The output voltage is programmed by two resistors (R1 from cathode to REF, R2 from REF to anode): VOUT = Vref x (1 + R1/R2). The reference input current (approximately 2uA) introduces a small error that can be compensated by adjusting R2. The device requires a minimum cathode current of 1mA for proper regulation.

Pin Description: TL431IDBVR Pin Definition and Functions
Pin Name Type Description
1 CATHODE I/O Shunt current / voltage output
2 NC — No internal connection (must tie to ANODE or float)
3 REF Input Reference threshold input (2.495V)
4 ANODE Power Common pin (normally ground)
5 NC — No internal connection
Application Scenarios: In which products and applications is TL431IDBVR used
  • Switching power supply optocoupler feedback with 2.495V reference and 0.2Ohm output impedance
  • Adjustable voltage regulator from 2.495V to 36V using external resistor divider
  • Precision Zener replacement with sharp turn-on and 100mA sink capability at 0.2Ohm impedance
  • Voltage monitoring circuit comparing divider output against 2.495V reference with 2% accuracy
Alternative Models: What chips are recommended as replacements for TL431IDBVR
Model Manufacturer Accuracy Temp Range Notes
TL431BIDBVR TI 0.5% -40 to +85C Higher accuracy
TL432AIDBVR TI 1% -40 to +85C Different pinout
KA431AZTA onsemi 1% -40 to +85C Pin-compatible
LT1009CS8 ADI 0.2% 0 to +70C Fixed 2.5V, higher accuracy

Recommend Parts

MCP6S26-I

6-channel PGA, SPI interface, gains 1-32V/V, 10MHz BW, rail-to-rail, 2.5-5.5V, SOIC-14

Brand: MICROCHIP

Package: SOIC-14 (150 mils body width)

IN STOCK: 6800pcs

Cargo cycle: 3-7 Days

The minimum order is 1

W25Q80VSSI

8Mbit Serial Flash, Quad SPI, 104MHz, SOIC-8, 2.7-3.6V

Brand: Winbond

Package: SOIC-8 208mil (5.3×8.0mm)

IN STOCK: 4316pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MM3Z9V1

9.1V 200mW Zener diode, SOD-323, onsemi/Diotec

Brand: ON

Package: SOD-323 (2.5 x 1.25 x 0.85 mm)

IN STOCK: 10735pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT89S51

8-bit 8051 MCU, 4KB ISP Flash, 128B RAM, 32 I/O, 2 timers, UART, watchdog timer, dual DPTR, 33MHz, ISP programming, PDIP-40, Atmel AT89S51.

Package: PDIP-40 / TQFP-44 / PLCC-44

IN STOCK: 15000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

GD32F303CBT6

Cortex-M4 32-bit MCU, 120MHz, 128KB Flash, 32KB SRAM, LQFP-48

Brand: gigadevice

Package: LQFP-48 (7x7mm, 0.5mm pitch)

IN STOCK: 3342pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MIC5205-3.3YM5-TR

3.3V 150mA ultra-low-noise LDO, 165mV dropout, 30uVrms noise, SOT-23-5

Brand: MICROCHIP

Package: SOT-23-5 (2.9 x 1.6 x 1.1mm)

IN STOCK: 9858pcs

Cargo cycle: 3-7 Days

The minimum order is 1