Opens in a new tab

TLC272CP

Dual LinCMOS op-amp, 1.8MHz GBW, R-R output, 0.6pA Ibias, PDIP-8

8500

Effective Inventory

Image for reference only

Manufacturer Part:

TLC272CP

Package:

PDIP-8 (9.81 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TLC272CP is a dual low-noise LinCMOS operational amplifier from Texas Instruments with rail-to-rail output, 1.8MHz bandwidth, and single/dual supply operation in a PDIP-8 package.

Key Specifications

Number of Amplifiers 2 (dual)
Technology LinCMOS
Supply Voltage Range 3V to 16V (single) or ±1.5V to ±8V (dual)
GBW 1.8MHz typical
Slew Rate 3.6V/µs typical
Input Offset Voltage 1.1mV typical (C-suffix), 10mV max
Input Bias Current 0.6pA typical
Input Noise (1kHz) 25nV/√Hz typical
Output Swing Rail-to-rail (within ~10mV of rails at light load)
Supply Current (per amp) 675µA typical at 5V
Phase Margin 48° typical
Operating Temperature 0°C to +70°C (C-suffix)
Package PDIP-8 (9.81 x 6.35mm)

Features

  • Dual LinCMOS op-amp in single 8-pin package
  • Rail-to-rail output swing
  • Extremely low input bias current (0.6pA typical)
  • 1.8MHz gain-bandwidth product
  • 3.6V/µs slew rate
  • Single or dual supply operation
  • Low supply current (675µA per amplifier)
  • Input common-mode range includes VDD
  • Internally compensated (no external capacitor)

Applications

  • High-impedance sensor amplifiers
  • Precision rectifiers and peak detectors
  • Active filters and oscillators
  • Sample-and-hold circuits
  • Battery-powered instrumentation
Product Introduction: TLC272CP Product Introduction

The TLC272CP from Texas Instruments is a dual LinCMOS operational amplifier combining the low input bias current of CMOS with the low noise of bipolar designs. The LinCMOS technology provides 0.6pA typical input bias current, making the device ideal for high-impedance sensor interfaces and sample-and-hold circuits. The 1.8MHz gain-bandwidth product and 3.6V/µs slew rate support audio-frequency and moderate-speed applications. The rail-to-rail output swing maximizes dynamic range in single-supply designs. The device operates from 3V to 16V single supply or ±1.5V to ±8V dual supply, with only 675µA per amplifier. The C suffix denotes the commercial temperature range (0°C to +70°C) and the P suffix denotes the PDIP-8 through-hole package.

Working Principle: TLC272CP Working Principle

The TLC272CP uses TI’s LinCMOS (Linear CMOS) process, which combines PMOS input transistors for extremely low input bias current with specialized output stage circuitry for near-rail-to-rail output swing. The input stage uses a differential pair of PMOS transistors, providing the 0.6pA gate leakage current. The input common-mode range extends from the negative rail to approximately VDD – 1.2V, covering most single-supply applications. The output stage uses a common-source PMOS pull-up and NMOS pull-down, allowing the output to swing within tens of millivolts of both supply rails under light load conditions. The internal compensation capacitor provides 48° phase margin, ensuring stability in unity-gain configurations without external components. The 1.8MHz GBW means the open-loop gain rolls off at 20dB/decade from approximately 10Hz, crossing 0dB at 1.8MHz. In a unity-gain configuration, the -3dB bandwidth is 1.8MHz; in a gain of 10 configuration, the bandwidth is approximately 180kHz.

Pin Description: TLC272CP Pin Definition and Functions
Pin Name Type Description
1 1OUT Output Amplifier 1 output
2 1IN- Input Amplifier 1 inverting input
3 1IN+ Input Amplifier 1 non-inverting input
4 GND/VSS Power Negative supply or ground
5 2IN+ Input Amplifier 2 non-inverting input
6 2IN- Input Amplifier 2 inverting input
7 2OUT Output Amplifier 2 output
8 VDD Power Positive supply (3V to 16V)

TLC272CP uses the PDIP-8 package with standard dual op-amp pinout: Pin 1 = Output A, Pin 2 = Inverting Input A (-), Pin 3 = Non-inverting Input A (+), Pin 4 = GND/VEE, Pin 5 = Non-inverting Input B (+), Pin 6 = Inverting Input B (-), Pin 7 = Output B, Pin 8 = VCC. This pinout is shared by LM358, TL072, NE5532, and all dual op-amps in DIP-8. The CMOS construction provides rail-to-rail output swing and very high input impedance (1TΩ typical). The C suffix denotes commercial temperature range (0°C to +70°C). For extended temperature, TLC272IP provides -40°C to +85°C. For quad version, TLC274 provides four CMOS op-amps in DIP-14.

Application Scenarios: In which products and applications is TLC272CP used
  • Sensor Amplifier: 0.6pA input bias current preserves signal from high-impedance pH electrodes, photodiodes, and piezo sensors
  • Active Filters: 1.8MHz GBW supports 2nd-order Butterworth filters up to ~100kHz cutoff frequency
  • Sample-and-Hold: Low bias current minimizes droop rate on hold capacitor; dual amps = buffer + hold
  • Single-Supply: Rail-to-rail output maximizes dynamic range in 3.3V or 5V battery-powered designs
  • Precision Rectifier: Low offset and high input impedance improve accuracy of super-diode rectifier circuits
Alternative Models: What chips are recommended as replacements for TLC272CP
Model Manufacturer Key Difference Package Specs
TLC272ACDR TI A-grade version with tighter offset voltage specifications for precision measurement circuits SOIC-8 1.8MHz/A-grade
TLC277CP TI Improved version with lower offset and higher output drive for demanding analog applications DIP-8 1.8MHz/improved
MCP6002-I/SN Microchip 1.8-6V dual rail-to-rail CMOS op-amp with 1MHz GBW for low-voltage signal processing SOIC-8 1MHz/1.8-6V
LM358N TI Bipolar dual op-amp with 3-32V single supply for general-purpose analog signal chains DIP-8 1.1MHz/bipolar
TLV2322IPWR TI Ultra-low-power 20kHz dual CMOS op-amp with 2µA supply for battery monitoring circuits TSSOP-8 20kHz/2µA

TLC272 is a dual CMOS rail-to-rail output op-amp with 1.8MHz GBW and 3-16V supply range. The AC-grade offers tighter offset specifications. For lower-voltage designs, MCP6002 operates down to 1.8V. For ultra-low-power battery applications, TLV2322 draws only 2µA per amplifier. The TLC272 is ideal for single-supply signal conditioning where input common-mode range includes ground.

Recommend Parts

MSP432P401RIPZR

Ultra-low-power Cortex-M4F MCU, 48MHz, 256KB Flash, 14-bit ADC, 850nA standby, 100-LQFP

Brand: TI

Package: 100-LQFP (14 x 14 x 1.4mm)

IN STOCK: 3750pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PTN78060WAH

4.5A positive-input buck-IT module, adjustable, SMD module

Brand: TI

Package: Module (34.3 x 19.3 x 8.2 mm)

IN STOCK: 4786pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC16F1526-I/PT

8-bit PIC16 MCU, 14KB Flash, 768B RAM, 30-ch 10-bit ADC, 10x CCP, 64-TQFP, XLP

Brand: MICROCHIP

Package: TQFP-64 (10.0 x 10.0 x 1.05 mm)

IN STOCK: 5600pcs

Cargo cycle: 3-7 Days

The minimum order is 1

R2A20178NP

8-channel 8-bit voltage output DAC, R-2R architecture, buffered rail-to-rail output, SPI interface up to 25MHz, 2.7-5.5V

Brand: Renesas

Package: 24-pin HWQFN (4x4x0.75mm)

IN STOCK: 6399pcs

Cargo cycle: 3-7 Days

The minimum order is 1

VS-40CPQ100-N3

Dual Schottky rectifier, common cathode, 2x20A, 100V, 0.61V VF, TO-247AC-3L, Vishay Q-series, 175 degC TJ, guard ring

Brand: VISHAY

Package: TO-247AC 3L (3-lead through-hole, 15.5mm width, tab for heatsink, common cathode configuration)

IN STOCK: 8950pcs

Cargo cycle: 3-7 Days

The minimum order is 1

BSC040N10NS5

OptiMOS 5 N-ch 100V 4mΩ 136A MOSFET, SuperSO8

Brand: infineon

Package: PG-TDSON-8 (SuperSO8, 5 x 6mm)

IN STOCK: 10509pcs

Cargo cycle: 3-7 Days

The minimum order is 1