Opens in a new tab

TLC59116IRHBR

16-Ch I2C LED Driver, 100mA, 8-bit PWM+Dot Correction, QFN-24

4567

Effective Inventory

Image for reference only

Manufacturer Part:

TLC59116IRHBR

Package:

QFN-24 (4.0 x 4.0 x 0.9 mm, 0.5mm pitch)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TLC59116IRHBR from Texas Instruments is a 16-channel I2C constant-current LED driver with 8-bit PWM dimming, 8-bit dot correction, and open/short detection in a QFN-24 package.

Key Specifications

Type 16-Channel I2C Constant-Current LED Driver
Channels 16 (current sink)
Max Current per Channel 100 mA (programmable via external resistor)
PWM Resolution 8-bit (256 steps)
Dot Correction 8-bit per channel
Interface I2C (up to 1 MHz Fast-mode Plus)
I2C Addresses 14 selectable (A0-A3 pins)
Output Voltage Up to 17V (LED supply)
Supply Voltage (Logic) 3.0 V to 5.5 V
Diagnostics Open-load, short-to-GND detection
Package QFN-24 (4 x 4 mm)
Operating Temperature -40C to +125C

Features

  • 16 independent constant-current LED outputs
  • 8-bit PWM dimming per channel (256 steps)
  • 8-bit dot correction for brightness matching
  • I2C Fast-mode Plus up to 1 MHz
  • 14 selectable I2C addresses for bus multiplexing
  • Open-load and short-to-GND detection
  • Thermal shutdown protection
  • Output enable for global dimming control

Applications

  • RGB LED matrix and display backlighting
  • Keypad illumination
  • General-purpose LED lighting control
  • Signage and decorative lighting
Product Introduction: TLC59116IRHBR Product Introduction

The TLC59116IRHBR from Texas Instruments is a 16-channel constant-current LED driver controlled via I2C interface. Each output provides up to 100 mA with current set by an external resistor. The 8-bit PWM controller provides 256 brightness steps per channel for smooth dimming, while the 8-bit dot correction compensates for LED brightness variations across channels. The I2C interface supports Fast-mode Plus at up to 1 MHz, and 14 selectable I2C addresses (via A0-A3 pins) allow multiple devices on a single bus. On-chip diagnostics detect open-load and short-to-GND conditions. The QFN-24 package provides a compact footprint for space-constrained applications. The thermal shutdown protects against excessive junction temperature.

Working Principle: TLC59116IRHBR Working Principle

The TLC59116IRHBR uses 16 DMOS transistors as current-sink outputs, each with an independent 8-bit PWM controller and 8-bit dot correction register. An external resistor (REXT) connected to the REXT pin sets the global maximum output current: IOUT(max) = 850 / REXT (for REXT in Ohms, IOUT in mA). The dot correction register scales the current from 0% to 100% of IOUT(max) in 256 steps, compensating for LED brightness bin variations. The PWM register independently controls the duty cycle of each output from 0/256 to 255/256, providing brightness control. The effective output current is IOUT(eff) = IOUT(max) x DotCorrection/255 x PWM/255. The I2C interface writes to control registers, PWM registers, and dot correction registers. Open-load detection works by briefly turning on the output and sensing if the voltage rises above a threshold, indicating no LED connected. Short-to-GND detection monitors if the output voltage stays near ground when the LED should be on.

Pin Description: TLC59116IRHBR Pin Definition and Functions
Pin Name Type Function
Multiple OUT0-OUT15 Output 16 LED current-sink outputs
Dedicated SDA/SCL I/O I2C data and clock
Dedicated A0-A3 Input I2C address selection
Dedicated REXT Input External current-set resistor
Dedicated OE Input Output enable (active LOW)
Dedicated VCC/GND Power 3.0-5.5V logic supply
Application Scenarios: In which products and applications is TLC59116IRHBR used
  • 16-segment RGB LED display driver with I2C control from MCU
  • White LED backlight array with dot correction for uniform brightness
  • Keypad backlighting with individual LED brightness control
  • Multi-device I2C bus LED driver (14 addresses for 224 LEDs)
Alternative Models: What chips are recommended as replacements for TLC59116IRHBR
Manufacturer Part Number Package Notes
TI TLC59116IPWR TSSOP-24 Same device, TSSOP package
NXP PCA9635PW TSSOP-28 16-ch, I2C, no dot correction
TI TLC5940NT DIP-28 16-ch, SPI, 12-bit PWM, grayscale
TI TLC59208ARGER QFN-20 8-ch, I2C, lower cost
ISSI IS31FL3733-QFLS4-TR QFN-44 12×16 matrix, I2C, animation

Recommend Parts

MCP6S26-I

6-channel PGA, SPI interface, gains 1-32V/V, 10MHz BW, rail-to-rail, 2.5-5.5V, SOIC-14

Brand: MICROCHIP

Package: SOIC-14 (150 mils body width)

IN STOCK: 6800pcs

Cargo cycle: 3-7 Days

The minimum order is 1

W25Q80VSSI

8Mbit Serial Flash, Quad SPI, 104MHz, SOIC-8, 2.7-3.6V

Brand: Winbond

Package: SOIC-8 208mil (5.3×8.0mm)

IN STOCK: 4316pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MM3Z9V1

9.1V 200mW Zener diode, SOD-323, onsemi/Diotec

Brand: ON

Package: SOD-323 (2.5 x 1.25 x 0.85 mm)

IN STOCK: 10735pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT89S51

8-bit 8051 MCU, 4KB ISP Flash, 128B RAM, 32 I/O, 2 timers, UART, watchdog timer, dual DPTR, 33MHz, ISP programming, PDIP-40, Atmel AT89S51.

Package: PDIP-40 / TQFP-44 / PLCC-44

IN STOCK: 15000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

GD32F303CBT6

Cortex-M4 32-bit MCU, 120MHz, 128KB Flash, 32KB SRAM, LQFP-48

Brand: gigadevice

Package: LQFP-48 (7x7mm, 0.5mm pitch)

IN STOCK: 3342pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MIC5205-3.3YM5-TR

3.3V 150mA ultra-low-noise LDO, 165mV dropout, 30uVrms noise, SOT-23-5

Brand: MICROCHIP

Package: SOT-23-5 (2.9 x 1.6 x 1.1mm)

IN STOCK: 9858pcs

Cargo cycle: 3-7 Days

The minimum order is 1