Opens in a new tab

TPS563219DDFR

3A 5.5V buck, D-CAP3, SOT-23-8, 600kHz, 0.6V ref, Eco-mode, power good, POL

5009

Effective Inventory

Image for reference only

Manufacturer Part:

TPS563219DDFR

Package:

SOT-23-8 (2.90 x 2.80 x 1.00 mm, 0.65mm pitch)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TPS563219DDFR from Texas Instruments is a 3A, 5.5V step-down converter in an SOT-23-8 package. With D-CAP3 control mode, it provides fast transient response without external compensation, ideal for space-constrained point-of-load applications.

Key Specifications

Input Voltage 2.7 V to 5.5 V
Output Current 3 A
Switching Frequency 600 kHz (fixed)
Reference Voltage 0.6 V (+/-1%)
Efficiency Up to 95%
Operating Temperature -40C to +125C

Features

  • 2.7V-5.5V input with 3A output in tiny SOT-23-8 package
  • D-CAP3 control mode for fast transient response without compensation
  • 600kHz fixed switching frequency for compact inductor selection
  • 0.6V +/-1% accurate feedback reference for precise output regulation
  • Auto-skip Eco-mode for high light-load efficiency
  • Power good output and programmable soft start

Applications

  • Point-of-load conversion from 3.3V or 5V rails
  • DDR memory VTT termination power supply
  • Space-constrained POL in networking and computing
  • Battery-powered system power regulation
Product Introduction: TPS563219DDFR Product Introduction

The TPS563219DDFR from Texas Instruments is a 3A, 2.7V-5.5V input step-down DC-DC converter in an ultra-compact SOT-23-8 package. The device uses TIs D-CAP3 control mode, a proprietary emulated current-mode control that provides fast transient response without external compensation components. This simplifies the design to just five external components: input capacitor, output capacitor, inductor, and two feedback resistors. The 600kHz fixed switching frequency balances efficiency and component size, enabling the use of small 1-2.2uH inductors and ceramic capacitors. The 0.6V feedback reference with +/-1% accuracy supports output voltages down to 0.6V, making the device suitable for low-voltage core and I/O rails in modern processors and FPGAs. Auto-skip Eco-mode reduces the effective switching frequency at light loads, maintaining high efficiency across the entire load range. The power good (PG) output provides real-time output voltage status for system sequencing and monitoring. The SOT-23-8 package (2.9mm x 2.8mm) enables the smallest possible solution footprint.

Working Principle: TPS563219DDFR Working Principle

The TPS563219DDFR uses D-CAP3 (emulated current-mode) control. (1) D-CAP3 Control: This proprietary control mode emulates the inductor current information from the output voltage ripple and internal ramp signal. Unlike traditional current-mode control, no current sense resistor or sense FET is needed. The emulated current information provides the advantages of current-mode control (cycle-by-cycle current limiting, improved line regulation) without the external compensation requirement. (2) Adaptive On-Time: The on-time is calculated adaptively based on the input voltage, output voltage, and switching frequency to maintain approximately constant frequency. This pseudo-fixed frequency operation simplifies EMI filter design. (3) Eco-Mode: At light loads, the device enters discontinuous conduction mode (DCM) where switching pulses are skipped to maintain regulation, improving light-load efficiency. (4) Power Good: The PG output is an open-drain transistor that pulls low when the output voltage falls below 85% or rises above 115% of the target.

Pin Description: TPS563219DDFR Pin Definition and Functions
Pin Name Type Function
1 GND Ground Ground (exposed pad)
2 VIN Power Input supply (2.7-5.5V)
3 SW Output Switch node (inductor)
4 PG Output Power good (open-drain)
5 FB Input Feedback voltage (0.6V ref)
6 SS I/O Soft-start (external cap)
7 EN Input Enable (active high)
8 BOOT Power Bootstrap capacitor
Application Scenarios: In which products and applications is TPS563219DDFR used
  • Point-of-load conversion from 3.3V or 5V rails to 0.6-3.3V at 3A
  • DDR memory VTT termination power supply with 0.6V reference
  • Space-constrained POL in networking and computing with SOT-23-8 footprint
  • Battery-powered system power regulation with Eco-mode efficiency
Alternative Models: What chips are recommended as replacements for TPS563219DDFR
Manufacturer Part Number Package Notes
TI TPS562219DDFR SOT-23-8 2A version, same family
TI TPS564201DDFR SOT-23-8 4A, similar
Monolithic Power MP2143GD-Z QFN-8 3A, 6V, 1.5MHz
Richtek RT5760AHPGJ5F SOT-23-8 3A, 5.5V, 1.5MHz

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1