Opens in a new tab

W5100S-L

Hardwired TCP/IP Ethernet controller, 4 sockets, 16KB buffer, SPI + parallel, 10/100 PHY, WIZnet W5100S, 48LQFP, WOL, -40~85 degC

5600

Effective Inventory

Image for reference only

Manufacturer Part:

W5100S-L

Package:

48-pin LQFP (7x7mm body, 0.5mm pitch, low-profile quad flat package, lead-free)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The W5100S-L is a hardwired TCP/IP embedded Ethernet controller from WIZnet that enables easy internet connectivity for embedded systems. This 3-in-1 device integrates a full hardware TCP/IP protocol stack, 10/100 Ethernet MAC, and Ethernet PHY in a single chip, providing a stable and reliable solution for adding network connectivity to embedded applications.

W5100S supports both SPI (Serial Peripheral Interface) and parallel system bus host interfaces, offering design flexibility. The SPI interface supports clock speeds up to 70 MHz for high-speed data transfer, while the 8-bit parallel bus provides even higher throughput for performance-critical applications. The device provides 4 independent hardware SOCKETs, each with its own memory buffer, enabling simultaneous multi-connection applications.

The hardwired TCP/IP stack supports TCP, UDP, WOL over UDP, ICMP, IGMPv1/v2, IPv4, ARP, and PPPoE protocols – all implemented in hardware, making the device immune to network attacks such as flooding, spoofing, and injection. With 16 KB of internal memory for packet buffering, integrated 10BaseT/100BaseTX PHY with auto-negotiation and Auto-MDIX, and low power consumption with Power Down mode and Wake-on-LAN support, the W5100S is ideal for IoT, industrial, and consumer embedded networking applications. The -L suffix denotes the 48-pin LQFP package.

Key Specifications

Parameter Value
Technology Hardwired TCP/IP + MAC + PHY (3-in-1)
Supported Protocols TCP, UDP, ICMP, IGMP, IPv4, ARP, PPPoE, WOL
Hardware Sockets 4 independent sockets
Internal Memory (TX/RX Buffer) 16 KB total
Host Interface SPI (up to 70 MHz) + 8-bit Parallel Bus
Ethernet PHY 10BaseT / 100BaseTX, integrated
Auto Negotiation Yes (10/100 Mbps, Full/Half Duplex)
Auto-MDIX Yes (in auto-negotiation mode)
Operating Voltage (VDD) 3.3 V
I/O Tolerance 5 V tolerant
SOCKET-less Commands ARP request, PING request
Power Down Mode Yes
Wake on LAN (WOL) Yes (over UDP)
Network Indicator LEDs Link, Speed, Duplex, Activity
Operating Temperature -40 degC to +85 degC
Package 48-pin LQFP (7 x 7 mm, 0.5 mm pitch)
Software Compatibility W5100 software compatible

Features

  • Full hardwired TCP/IP stack (TCP, UDP, ICMP, IGMP, IPv4, ARP, PPPoE)
  • Integrated 10/100 Ethernet MAC and PHY (3-in-1 solution)
  • 4 independent hardware SOCKETs simultaneously
  • 16 KB internal memory for TCP/IP packet processing
  • High-speed SPI host interface (up to 70 MHz, mode 0/3)
  • 8-bit parallel system bus host interface (2 address lines + 8-bit data)
  • Hardware network security – immune to flooding/spoofing
  • SOCKET-less commands: ARP request, PING request
  • Auto-negotiation (10/100 Mbps, full/half duplex)
  • Auto-MDIX (crossover detection)
  • Power Down mode and Wake on LAN over UDP
  • 3.3 V operation, 5 V tolerant I/O
  • Network status LED outputs (LINK, SPD, DPLX, ACT)
  • Low heat dissipation vs. competing solutions
  • Software compatible with W5100 (no code changes needed)
  • 48-pin LQFP lead-free package (7 x 7 mm, 0.5mm pitch)
  • Industrial temperature range: -40 degC to +85 degC

Applications

  • IoT devices and smart home appliances
  • Industrial automation and factory networking
  • Serial-to-Ethernet converters
  • Embedded web servers and remote monitoring
  • Security systems and IP cameras
  • POS terminals and payment devices
  • Industrial sensors and data acquisition
  • Arduino / MCU Ethernet shields and modules
Product Introduction: W5100S-L Product Introduction

The W5100S-L is a hardwired TCP/IP embedded Ethernet controller from WIZnet, designed to provide easy and reliable internet connectivity for embedded systems. As a 3-in-1 solution integrating a full hardware TCP/IP protocol stack, Ethernet MAC, and 10/100 Ethernet PHY, the W5100S offloads the entire network protocol processing from the host microcontroller, dramatically simplifying embedded Ethernet design.

Unlike software-based TCP/IP stacks that consume significant MCU resources and are vulnerable to network attacks, WIZnet’s patented hardwired TCP/IP technology implements the protocol stack entirely in hardware. This provides stable, deterministic network performance and inherent security against common network threats such as SYN flooding, IP spoofing, and protocol injection attacks. The supported protocols include TCP, UDP, ICMP, IGMPv1/v2, IPv4, ARP, and PPPoE.

The W5100S provides four independent hardware SOCKETs, each with configurable send/receive buffer sizes allocated from the 16KB internal shared memory. This enables multiple simultaneous network connections such as a web server, TCP data connection, and UDP broadcast all running concurrently.

Two host interface options are available: a high-speed SPI interface supporting up to 70MHz clock speed, and an 8-bit parallel system bus with 2 address lines for even higher throughput. The device’s I/O pins are 5V tolerant, simplifying interfacing with both 3.3V and 5V microcontrollers.

Additional features include Power Down mode for low power consumption, Wake-on-LAN over UDP for remote activation, SOCKET-less commands (ARP and PING) for basic network diagnostics without opening a socket, and integrated network status LED drivers. The W5100S is software-compatible with the earlier W5100, meaning existing application code can run without modification. The -L variant is packaged in a 48-pin LQFP measuring 7 x 7mm with 0.5mm pitch.

Working Principle: W5100S-L Working Principle

The W5100S operates as a network offload engine, handling all Ethernet and TCP/IP protocol processing in dedicated hardware, freeing the host microcontroller for application tasks. Here’s how it works:

1. Hardwired TCP/IP Stack: The core of the W5100S is WIZnet’s proprietary hardwired TCP/IP stack, implemented entirely in hardware logic. Unlike software TCP/IP stacks that run on the host MCU, this hardware implementation processes protocols at wire speed with deterministic latency. The stack handles TCP (including connection management, retransmission, windowing), UDP, ICMP (ping), IGMP (multicast), ARP (address resolution), and PPPoE without any host software intervention.

2. Hardware Sockets: The W5100S provides four independent hardware sockets (SOCKET 0-3). Each socket can be configured independently for TCP server, TCP client, UDP, MACRAW, or PPPoE mode. Each socket has its own set of registers and can be assigned a configurable portion of the 16KB internal memory for transmit and receive buffering. This allows up to four simultaneous network connections.

3. Memory Architecture: A 16KB block of dual-port RAM serves as shared TX/RX buffer memory across all sockets. The memory is divided between transmit and receive buffers, with each socket’s allocation programmable via register settings. The host MCU accesses this memory through indirect addressing (via read/write pointer registers) over either the SPI or parallel interface.

4. Ethernet PHY (Physical Layer): The integrated 10BaseT/100BaseTX PHY handles all physical layer functions including encoding/decoding, clock recovery, link detection, and auto-negotiation. Auto-negotiation automatically selects the highest performance common mode (10/100 Mbps, full/half duplex) between the W5100S and the connected network device. Auto-MDIX automatically corrects for straight-through vs. crossover cable connections.

5. Host Interface – SPI: The SPI interface operates in mode 0 or mode 3 with clock speeds up to 70MHz. Communication uses a simple protocol where the host sends an address phase followed by read/write data. This is the simplest interface requiring only 4 wires (SCLK, MOSI, MISO, /SCS) plus optional interrupt.

6. Host Interface – Parallel Bus: For higher performance, the 8-bit parallel bus interface uses two address lines (A0/A1) plus 8 data lines and control signals (/RD, /WR, /CS). This provides faster data transfer than SPI, suitable for high-throughput applications.

7. Power Management: The W5100S supports a Power Down mode that shuts down most internal circuitry to minimize power consumption. In this state, the device can be awakened via Wake-on-LAN (a special UDP packet) or by the host MCU toggling a control signal. Normal operation current is also optimized for low power dissipation.

Pin Description: W5100S-L Pin Definition and Functions
Pin Group Pin Name(s) Type Description
Power VDD (3.3V) Power Core and I/O supply voltage: 3.3V. Multiple VDD pins – all must be connected. Bypass each with 0.1uF ceramic caps.
Power GND Ground Ground reference. Multiple GND pins – all must be connected to ground plane.
SPI Interface SCLK Input SPI clock input. Up to 70 MHz. Connect to MCU SPI clock.
SPI Interface MOSI Input SPI master-out slave-in data input. Connect to MCU MOSI.
SPI Interface MISO Output SPI master-in slave-out data output. Connect to MCU MISO.
SPI Interface /SCS Input SPI chip select, active low. Connect to MCU GPIO for chip selection.
Parallel Bus AD0-AD7 I/O 8-bit multiplexed address/data bus (used only in parallel mode).
Parallel Bus A0-A1 Input Address lines for register selection (parallel mode).
Parallel Bus /WR, /RD, /CS Input Write strobe, read strobe, and chip select (parallel mode).
Interrupt /INT Output Interrupt output, active low. Asserts when socket events occur (connect, disconnect, receive data, timeout, etc.). Connect to MCU interrupt pin.
Reset /RESET Input Active-low reset input. Connect to reset controller or RC reset circuit.
Ethernet PHY TXP, TXN Output Differential transmit pair for 10/100BaseTX. Connect to RJ45 transformer / magnetics.
Ethernet PHY RXP, RXN Input Differential receive pair for 10/100BaseTX. Connect to RJ45 transformer / magnetics.
Clock XTALO, XTALI I/O Crystal oscillator interface. Connect 25MHz crystal with load caps, or external 25MHz clock input.
LEDs LINK, SPD, DPLX, ACT Output Network status LED drivers: Link status, Speed (10/100), Duplex, Activity. Drive LEDs with current-limiting resistors to VDD.
Mode Select TESTMODE[3:0] Input Test mode / interface select pins. Tie to appropriate levels for SPI or parallel mode selection.
Power Mgmt PWDN Input Power down mode control input. High = power down, low = normal operation.

Package: 48-pin LQFP (Low-profile Quad Flat Package). Body dimensions: 7mm x 7mm, 0.5mm lead pitch. -L suffix designates LQFP package (vs -Q for QFN). Lead-free, RoHS compliant.

Application Scenarios: In which products and applications is W5100S-L used
  • Serial-to-Ethernet Converters: Serial (UART/RS-232/RS-485) to Ethernet protocol converters used for connecting legacy serial devices to IP networks, including industrial device servers, MODBUS gateways, and remote equipment monitoring interfaces, where the hardwired TCP/IP stack guarantees reliable, deterministic performance without MCU overhead.
  • IoT and Smart Home Devices: Network connectivity for smart home appliances, HVAC systems, security cameras, door locks, and energy management devices, where low cost, small footprint, and hardware TCP/IP security are essential for reliable and secure IoT node implementation.
  • Industrial Automation: Ethernet connectivity for PLCs, remote I/O modules, industrial sensors, and factory floor equipment, supporting industrial Ethernet protocols and Modbus TCP, with the -40 degC to +85 degC industrial temperature range and robust hardware stack ensuring operation in harsh factory environments.
  • Embedded Web Servers: Remote configuration and monitoring interfaces for embedded equipment, where the W5100S hosts a lightweight web server allowing users to access device status, update firmware, and change settings through a standard web browser.
  • Arduino/Evaluation Shields and Modules: Ethernet shields for Arduino, Raspberry Pi Pico, and other development platforms, enabling hobbyists, students, and engineers to quickly add wired Ethernet connectivity to their projects using WIZnet’s well-documented ioLibrary_Driver software stack.
  • POS Terminals and Payment Devices: Network connectivity for point-of-sale terminals, card readers, and payment processing equipment, where the hardware-offloaded TCP/IP stack reduces MCU load and provides the reliable connectivity required for financial transaction processing.
  • Data Acquisition and Sensor Networks: Industrial data loggers, environmental monitoring systems, and distributed sensor networks that need to transmit collected data to a central server over Ethernet, with the 4 independent sockets supporting multiple simultaneous data streams or protocols.
  • Security and Access Control Systems: Network connectivity for IP cameras, access control panels, intercom systems, and security alarm panels, where the stable hardware TCP/IP stack and resistance to network attacks provide enhanced reliability for security-critical applications.
Alternative Models: What chips are recommended as replacements for W5100S-L
Manufacturer Part Number HW Sockets Buffer Host I/F Package Notes
WIZnet W5100S-Q 4 16 KB SPI + Parallel 48-QFN Same die, QFN package
WIZnet W5500 8 32 KB SPI only 48-LQFP More sockets/buffer, SPI only
WIZnet W6100 8 32 KB SPI + Parallel 48-LQFP IPv4 + IPv6 dual stack
WIZnet W5100 4 16 KB SPI + Parallel 48-LQFP Previous generation
Microchip ENC28J60 0 (SW stack) 8 KB SPI 28-SOIC MAC+PHY only, needs SW TCP/IP
WIZnet W7500 8 32 KB Internal 64-LQFP SoC with ARM Cortex-M0 MCU built-in

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1