Opens in a new tab

TPS51200DRC

Sink/source DDR termination regulator, DDR/DDR2/DDR3/DDR4 VTT, 3A, VSON-10 (3×3 mm)

10766

Effective Inventory

Image for reference only

Manufacturer Part:

TPS51200DRC

Package:

VSON-10 (3 x 3 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

The TPS51200DRC is a 3A sink/source DDR termination regulator from Texas Instruments in a VSON-10 (3×3 mm) package with exposed thermal pad. It generates the VTT bus termination voltage for DDR, DDR2, DDR3, DDR3L, LPDDR3, and DDR4 memory systems. Key features include VLDOIN range 1.1V-3.5V, ±10 mA buffered REFOUT (VTTREF), remote sensing (VOSNS), droop compensation, PGOOD monitoring, EN-controlled S3 discharge, soft-start, UVLO, OCL, and thermal shutdown. Requires only 20 µF minimum output capacitance (3 x 10 µF MLCCs). Operating range: -40°C to +85°C. Green and Pb-free rated, MSL-2.

Product Introduction: TPS51200DRC Product Introduction

The TPS51200DRC is a sink and source Double Data Rate (DDR) termination regulator manufactured by Texas Instruments, specifically designed for low input voltage, low-cost, low-noise systems where space is a key consideration. It maintains a fast transient response and requires a minimum output capacitance of only 20 µF (typically 3 x 10 µF MLCCs), making it one of the most compact and cost-effective VTT regulation solutions available.

The device integrates a high-performance low-dropout (LDO) linear regulator capable of both sourcing and sinking current up to 3 A, making it ideal for DDR memory bus termination applications. The output voltage (VO) tracks the reference input (REFIN) voltage, which can be connected directly to the memory supply voltage (VDDQ) or through a resistor divider, providing flexibility for DDR, DDR2, DDR3, DDR3L, LPDDR3, and DDR4 VTT applications.

Key features include a VLDOIN voltage range of 1.1V to 3.5V supporting both 2.5V and 3.3V power rails, a ±10 mA buffered reference output (REFOUT) for generating the VTTREF reference voltage used by DDR memory controllers, remote voltage sensing (VOSNS) for tight regulation at the load, built-in droop compensation, soft-start current limiting, undervoltage lockout (UVLO), overcurrent protection (OCL), and thermal shutdown.

The TPS51200 provides an open-drain PGOOD signal to monitor output regulation status and an EN (enable) input that can be used to discharge VTT during S3 (suspend-to-RAM) state for DDR power management. The DRC package is a thermally efficient 10-pin VSON (Very thin Small Outline No-lead) with exposed thermal pad, measuring 3.00 x 3.00 mm. The device operates from -40°C to +85°C and is rated both Green and Pb-free.

Working Principle: TPS51200DRC Working Principle

The TPS51200DRC operates as a bidirectional (sink/source) linear termination voltage regulator, generating the VTT bus termination voltage for DDR memory systems.

Output Voltage Regulation: The output voltage (VO) is regulated to match the reference input (REFIN). For standard DDR termination, REFIN is typically connected to a resistor divider from VDDQ (the memory supply voltage) such that REFIN = VDDQ / 2. The internal error amplifier compares the sensed output voltage (via VOSNS) against the REFIN-derived reference, driving the pass element to source or sink current as needed to maintain VO = VDDQ / 2. This half-VDDQ tracking is the standard VTT voltage required by DDR memory specifications.

Sink and Source Capability: Unlike unidirectional LDO regulators, the TPS51200 can both source current (when VTT load demands more current, e.g., driving DQ lines LOW) and sink current (when VTT load returns current, e.g., driving DQ lines HIGH). This bidirectional capability is essential for DDR termination, where the termination resistors connected to VTT must both absorb and supply current depending on the data bus state. The integrated high-side and low-side pass elements enable this sink/source operation without external components.

Droop Compensation: The device includes built-in droop compensation that pre-adjusts the output voltage slightly higher under heavy sink conditions and slightly lower under heavy source conditions. This anticipatory compensation counteracts the parasitic resistance in PCB traces and vias, maintaining tighter effective regulation at the DDR DIMM termination point.

Reference Output (REFOUT): The REFIN voltage is buffered and output on the REFOUT pin, providing a ±10 mA buffered reference voltage (VTTREF) for DDR memory controllers. REFOUT becomes active when REFIN exceeds 0.390V and VIN is above the UVLO threshold. When REFOUT drops below 0.375V, it is disabled and discharged to GND through an internal 10 kΩ MOSFET. A 0.1 µF ceramic capacitor to GND is required on REFOUT for stability. REFOUT operation is independent of the EN pin state.

Soft-Start Sequencing: At startup, a current clamp implements soft-start by limiting the output current to a low constant value, allowing the output capacitors to charge linearly. This prevents inrush current spikes that could damage the device or cause system voltage rail droops. Once the output reaches the target voltage, the current clamp is released and the regulator enters normal operation.

S3/S5 Power State Support: The EN pin serves dual purpose: when HIGH, the VO regulator is enabled; when LOW (connected to SLP_S3 signal), the VO regulator is disabled and VTT is discharged through an internal MOSFET to GND. This discharge path ensures VTT returns to 0V during suspend-to-RAM (S3) state, meeting DDR power sequencing requirements. REFOUT remains active during S3 state as it is independent of EN.

Power Good (PGOOD): The open-drain PGOOD output goes HIGH-impedance (after a 1 ms deglitch delay) when VO is within ±5% of the target voltage, indicating proper regulation. PGOOD goes LOW (asserted) when VO is out of regulation, during UVLO, during thermal shutdown, or when EN is LOW.

Protection Mechanisms: UVLO disables the device when VIN drops below the threshold (approximately 2.1V), preventing erratic operation during power-up/power-down. Overcurrent protection (OCL) limits the output current to prevent damage during fault conditions. Thermal shutdown disables the device when junction temperature exceeds approximately 150°C, with automatic recovery when temperature drops.

Pin Description: TPS51200DRC Pin Definition and Functions
Pin Name Type Default Function Description
1 REFIN I Reference Input Sets the target output voltage; connect to VDDQ/2 via resistor divider or directly; range 0.5V to 1.8V
2 VLDOIN I LDO Supply Input Power supply for the LDO regulator; range 1.1V to 3.5V; connect to VDDQ or VDD for DDR3/DDR4
3 VO O LDO Output Termination voltage output (VTT); source/sink up to 3A; connect to DDR termination bus
4 PGND G Power Ground Power ground for the LDO; connect to thermal pad and system GND
5 VOSNS I Voltage Sense Input Remote sensing of output voltage; connect to positive terminal of output capacitor or load for tight regulation
6 REFOUT O Reference Output Buffered reference output (VTTREF); ±10 mA drive; requires 0.1 µF ceramic cap to GND; max total cap 0.47 µF
7 EN I Enable Input Enable/disable control; connect to SLP_S3 for DDR VTT control; LOW = VO disabled and discharged
8 GND G Signal Ground Signal ground reference
9 PGOOD O Power Good Open-drain output; HIGH-Z when VO in regulation (±5%); requires external pull-up resistor
10 VIN I Power Supply 2.5V or 3.3V main power supply; requires 1 µF to 4.7 µF ceramic decoupling capacitor
Pad Thermal Pad G Thermal/PGND Exposed thermal pad; connect to PGND and system GND plane for heat dissipation
Application Scenarios: In which products and applications is TPS51200DRC used
Application Description
DDR3/DDR4 VTT Termination Primary application: generating and regulating VTT bus termination voltage for DDR3 (0.75V), DDR3L (0.675V), LPDDR3 (0.6V), and DDR4 (0.6V) memory systems in notebooks, desktops, and servers
DDR2 VTT Termination Generating 0.9V VTT for DDR2 memory systems with 1.8V VDDQ; REFIN set to VDDQ/2 via resistor divider
Embedded DDR Memory VTT regulation for embedded systems, SoC boards, and compute modules using DDR3/DDR4 with minimal external components
Telecom and Networking VTT supply for DDR memory in routers, switches, base stations, and telecom equipment; supports S3 power state for energy savings
General-Purpose LDO Can be used as a general-purpose sink/source LDO for applications requiring bidirectional current capability and tight tracking regulation
Alternative Models: What chips are recommended as replacements for TPS51200DRC
Model Manufacturer Compatibility Key Difference
TPS51200A TI Pin-Compatible / Drop-in Upgrade Enhanced robustness version; same package and function; recommended for new designs
TPS51200DRCR TI Pin-Compatible / Identical Large tape and reel packaging (3,000/reel) vs small reel (250/reel); same silicon
TPS51100 TI Functionally Similar Earlier generation; higher VIN min (4.75V); MSOP-10 PowerPAD package; not suitable for 2.5V rail
TPS51200-Q1 TI Pin-Compatible Automotive qualified (AEC-Q100); -40°C to +125°C; same functionality with automotive grade
NCP51399 onsemi Functionally Similar DDR3/DDR4 termination regulator; 3A sink/source; DFN-10 package; different pinout

Recommend Parts

ISL95855HRTZ-T

IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN

Brand: Renesas

Package: 48-TQFN (6×6 mm, exposed pad)

IN STOCK: 2156pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4019PBF

150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 2409pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSP430F247TPMR

TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64

Package: See datasheet

IN STOCK: 13371pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NUC029LAN

ARM Cortex-M0 MCU, 50MHz, 64KB Flash, 4KB SRAM, dual UART/SPI/I2C, LQFP-48

Brand: Nuvoton

Package: LQFP-48 (7.0 x 7.0 x 1.45 mm)

IN STOCK: 12385pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT45DB081E-SHN-T

8Mbit DataFlash, dual-SPI 85MHz, 2x264B SRAM buffers, USON-8 (4x3mm), page-based ECC

Brand: Renesas

Package: USON-8 (4 x 3 x 0.6mm, 0.8mm pitch)

IN STOCK: 4500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1