Opens in a new tab

TLC2252CD

Dual rail-to-rail output micropower op-amp, Advanced LinCMOS, 4.4-16V, SOIC-8, 35µA/ch

300

Effective Inventory

Image for reference only

Manufacturer Part:

TLC2252CD

Package:

SOIC-8 (4.9 x 3.9 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

The TLC2252CD is a dual rail-to-rail output micropower operational amplifier from Texas Instruments in an SOIC-8 package. Built on Advanced LinCMOS process, it features 35 µA/channel supply current, 200 kHz GBW, 0.12 V/µs slew rate, input bias current of 1 pA typical, and 19 nV/√Hz input noise at 1 kHz. The input common-mode range includes the negative rail and the output swings to both supply rails, maximizing dynamic range in single-supply applications. Supply range: 4.4V-16V (single) or ±2.2V to ±8V (dual). Commercial temperature range: 0°C to +70°C. Offset voltage: 1.5 mV max (850 µV for A-grade). Ideal for battery-powered instrumentation, high-impedance sensor conditioning, and ADC buffering.

Product Introduction: TLC2252CD Product Introduction

The TLC2252CD is a dual rail-to-rail output very low-power operational amplifier from Texas Instruments, built on the Advanced LinCMOS process. It is part of the TLC225x family, which includes the TLC2252 (dual) and TLC2254 (quad) variants. The device is fully characterized at both 5V and ±5V supply voltages and optimized for low-voltage, battery-powered applications.

The TLC2252 features rail-to-rail output swing that includes both supply rails, maximizing dynamic range in single-supply or split-supply configurations. The common-mode input voltage range extends to the negative rail (V-), enabling direct ground-referenced sensing in single-supply systems. Each channel consumes only 35 µA of supply current (typical), making it one of the lowest-power dual op-amps available in its class.

Key specifications include a gain-bandwidth product of 200 kHz, a slew rate of 0.12 V/µs, input offset voltage of 1.5 mV max (850 µV for the A-grade TLC2252A), input bias current of 1 pA typical (60 pA max), and equivalent input noise of 19 nV/√Hz at 1 kHz. The low input bias current, a characteristic of the CMOS input stage, makes the TLC2252 ideal for high-impedance signal conditioning from sources such as piezoelectric transducers, photodiodes, and pH probes.

The CD suffix denotes the SOIC-8 plastic surface-mount package rated for the commercial temperature range of 0°C to +70°C. The D package code refers to the standard 8-pin SOIC (Small Outline Integrated Circuit) with gull-wing leads. The tube packaging option is standard for this variant. The TLC2252CD supports both single-supply (4.4V to 16V) and dual-supply (±2.2V to ±8V) operation, providing flexibility across a wide range of analog signal conditioning applications.

Compared to earlier generation micropower CMOS op-amps such as the TLC27L2 or TS27L2, the TLC2252 offers significantly improved noise performance (19 nV/√Hz vs typical >50 nV/√Hz), rail-to-rail output for increased dynamic range, and lower input offset voltage. For precision applications requiring tighter offset, the TLC2252A variant offers 850 µV max offset at 25°C.

Working Principle: TLC2252CD Working Principle

The TLC2252CD operates as a dual-channel CMOS operational amplifier using Texas Instruments Advanced LinCMOS process, combining micropower consumption with rail-to-rail output capability.

CMOS Input Stage: The input stage uses a differential pair of P-channel MOSFETs, providing extremely high input impedance (typically 10^12 Ω) and very low input bias current (1 pA typical). This CMOS input architecture eliminates the input bias current errors that plague bipolar op-amps in high-impedance circuits. The input common-mode voltage range extends from the negative rail (V-) to approximately 1.2V below the positive rail (V+), enabling ground-referenced operation in single-supply applications. The input offset voltage is laser-trimmed to 850 µV max (A-grade) or 1.5 mV max (standard grade) at 25°C.

Rail-to-Rail Output Stage: The output stage uses a complementary CMOS push-pull configuration with both P-channel and N-channel output transistors. This architecture allows the output to swing to within millivolts of both supply rails under light load conditions (typically 10 mV from V- and 60 mV from V+ with 100 kΩ load). The rail-to-rail output maximizes the usable signal range in single-supply applications, which is critical when interfacing with ADCs where even a few hundred millivolts of lost dynamic range can significantly reduce resolution.

Micropower Operation: The TLC2252 achieves its very low supply current (35 µA per channel, 80 µA total for dual) through careful biasing of the internal gain stages at very low quiescent current levels. This micropower design makes the device ideal for battery-powered applications where supply current must be minimized. The trade-off for low power is reduced bandwidth (200 kHz GBW) and slew rate (0.12 V/µs), which are adequate for DC and low-frequency signal conditioning.

Gain-Bandwidth Product: The 200 kHz gain-bandwidth product defines the frequency at which the open-loop gain drops to unity (0 dB). For a closed-loop gain of 10 (20 dB), the bandwidth is approximately 20 kHz; for a gain of 100 (40 dB), approximately 2 kHz. The TLC2252 is therefore best suited for DC and low-frequency applications such as sensor signal conditioning, transducer amplification, and active filtering below audio frequencies.

Slew Rate: The 0.12 V/µs slew rate limits the maximum output swing at high frequencies. For a full-scale sine wave output, the maximum frequency before slew-rate limiting is f_max = SR / (2π × Vp), where Vp is the peak output voltage. For a 5V peak-to-peak output (Vp = 2.5V), the maximum frequency is approximately 7.6 kHz. This is consistent with the device target application space of DC and low-frequency signal conditioning.

Noise Performance: The TLC2252 achieves 19 nV/√Hz input-referred voltage noise at 1 kHz, which is approximately four times lower than competing micropower CMOS op-amps. This improvement is achieved through optimized input transistor sizing and bias current distribution. The low noise, combined with the high input impedance, makes the device excellent for amplifying small signals from high-impedance sources such as piezoelectric sensors and photodiodes without significant noise degradation.

Pin Description: TLC2252CD Pin Definition and Functions
Pin Name Type Default Function Description
1 1OUT O Channel 1 Output Output of amplifier channel 1; rail-to-rail swing
2 1IN- I Channel 1 Inverting Input Inverting input of amplifier channel 1; high-impedance CMOS input
3 1IN+ I Channel 1 Non-Inverting Input Non-inverting input of amplifier channel 1; common-mode range includes V-
4 V- P Negative Supply / GND Negative power supply (dual supply) or ground (single supply); 0V in single-supply config
5 2IN+ I Channel 2 Non-Inverting Input Non-inverting input of amplifier channel 2
6 2IN- I Channel 2 Inverting Input Inverting input of amplifier channel 2
7 2OUT O Channel 2 Output Output of amplifier channel 2; rail-to-rail swing
8 V+ P Positive Supply Positive power supply; 4.4V to 16V single supply or up to ±8V dual supply
Application Scenarios: In which products and applications is TLC2252CD used
Application Description
Battery-Powered Instrumentation Micropower op-amp for portable medical devices, handheld meters, and field instruments where 35 µA/ch supply current extends battery life significantly
Sensor Signal Conditioning High-impedance input (1 pA bias current) ideal for piezoelectric transducers, photodiodes, pH electrodes, and other high-Z sensors requiring minimal input loading
ADC Input Buffering Rail-to-rail output maximizes ADC dynamic range in single-supply data acquisition systems; drives ADC sample-and-hold capacitors directly
Portable Monitoring Remote sensing and environmental monitoring nodes where ultra-low quiescent current and wide supply range (4.4-16V) enable long unattended operation
Low-Frequency Active Filtering 200 kHz GBW suitable for active low-pass, band-pass, and notch filters in DC and low-frequency signal paths below audio range
Alternative Models: What chips are recommended as replacements for TLC2252CD
Model Manufacturer Compatibility Key Difference
TLC2252CDR TI Pin-Compatible / Electrically Identical Tape and reel packaging (2500/reel) instead of tube; same silicon and specs; preferred for SMT production
TLC2252ACD TI Pin-Compatible A-grade with tighter offset voltage (850 µV max vs 1.5 mV); same package and pinout; for precision applications
TLV2252CD TI Pin-Compatible Lower minimum supply voltage (2.7V vs 4.4V); optimized for 3V/5V operation; same rail-to-rail output and low power
TLC27L2CD TI Pin-Compatible Predecessor device; higher noise, no rail-to-rail output; TLC2252 is recommended upgrade per TI
MCP6022 Microchip Functionally Similar Dual rail-to-rail op-amp, 1.8-6V supply, 10 MHz GBW; much wider bandwidth but higher supply current (1 mA/ch)

Recommend Parts

ISL95855HRTZ-T

IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN

Brand: Renesas

Package: 48-TQFN (6×6 mm, exposed pad)

IN STOCK: 2156pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4019PBF

150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 2409pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSP430F247TPMR

TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64

Package: See datasheet

IN STOCK: 13371pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NUC029LAN

ARM Cortex-M0 MCU, 50MHz, 64KB Flash, 4KB SRAM, dual UART/SPI/I2C, LQFP-48

Brand: Nuvoton

Package: LQFP-48 (7.0 x 7.0 x 1.45 mm)

IN STOCK: 12385pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT45DB081E-SHN-T

8Mbit DataFlash, dual-SPI 85MHz, 2x264B SRAM buffers, USON-8 (4x3mm), page-based ECC

Brand: Renesas

Package: USON-8 (4 x 3 x 0.6mm, 0.8mm pitch)

IN STOCK: 4500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1