Opens in a new tab

TPS23751PWPR

IEEE 802.3at PoE PD interface with flyback DC-DC controller, 25.5W, 0.5-ohm hotswap MOSFET, 16-HTSSOP, -40~85C

1976

Effective Inventory

Image for reference only

Manufacturer Part:

TPS23751PWPR

Package:

16-HTSSOP (PWP) (5.0 x 4.4 mm) with PowerPAD

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

The TPS23751PWPR from Texas Instruments is an integrated IEEE 802.3at PoE Powered Device (PD) interface and current-mode flyback DC-DC controller in a 16-pin HTSSOP package with PowerPAD. The device supports both 802.3at Type 2 (25.5W) and 802.3af Type 1 (13W) PoE standards, featuring an internal 0.5-ohm 100V hotswap MOSFET that eliminates the need for an external pass transistor. The PoE interface implements type-2 hardware classification, detection signature, and auxiliary power detect (APD) for adapter ORing. The DC-DC controller provides current-mode control with slope compensation, programmable switching frequency, internal soft-start, and variable frequency operation (VFO) for high light-load efficiency. The SRD output automatically controls external synchronous rectifiers. UVLO thresholds: 38.1V turn-on, 32V turn-off. Inrush current: 140mA typical. Operating current limit: 850mA minimum. Operating temperature: -40C to 85C. Tape and reel, 2000/reel. RoHS compliant, EAR99.

Product Introduction: TPS23751PWPR Product Introduction

The TPS23751PWPR is an integrated Power-over-Ethernet (PoE) powered device (PD) interface and current-mode flyback DC-DC controller from Texas Instruments, housed in a 16-pin HTSSOP package with PowerPAD for thermal dissipation. The device supports both IEEE 802.3at (PoE+) Type 2 and IEEE 802.3af (PoE) Type 1 standards, capable of powering PDs up to 25.5W.

The PoE interface section implements type-2 hardware classification per IEEE 802.3at, with a detection signature resistor (24.9 kohm on DEN pin), programmable classification current (CLS pin resistor), and auxiliary power detect (APD) input for adapter ORing. The integrated 0.5-ohm, 100V hotswap MOSFET minimizes power dissipation and eliminates the need for an external pass transistor. The inrush current is typically limited to 140 mA, and the operating current limit is a minimum of 850 mA.

The DC-DC controller section features current-mode control with slope compensation, internal soft-start, a bootstrap startup current source, and programmable switching frequency via the RT pin resistor. The controller drives an external N-channel MOSFET through the GATE pin and supports both PWM mode for heavy loads and variable frequency operation (VFO) for improved light-load efficiency. The synchronous rectifier disable (SRD) output automatically disables external synchronous rectifiers during VFO mode to prevent reverse current flow.

Key protection features include thermal shutdown, undervoltage lockout (UVLO) with 38.1V turn-on and 32V turn-off thresholds, VCC overvoltage protection, and output overvoltage protection. The T2P (Type 2 PSE) active-low output indicates when a type-2 PSE is connected or when the APD is active. The PWP package is a 16-pin HTSSOP with an exposed thermal pad (PowerPAD) that must be connected to VSS. The PWPR suffix denotes tape and reel packaging with 2,000 units per reel.

Working Principle: TPS23751PWPR Working Principle

The TPS23751PWPR integrates two major functional blocks: a PoE PD interface and a flyback DC-DC controller, operating together to convert PoE power from an Ethernet cable into a regulated isolated DC output.

PoE PD Interface: When connected to a Power Sourcing Equipment (PSE) through the Ethernet cable, the PD interface first presents a detection signature (24.9 kohm between VDD and VSS) to identify itself as a valid PoE device. After detection, the PSE applies classification voltage, and the CLS pin resistor programs the classification current to signal the PD power class (Class 0-4 for 802.3af, or Class 4 for 802.3at Type 2 at 25.5W). Once classification is complete, the PSE applies full power (44-57V). The internal 0.5-ohm, 100V hotswap MOSFET between RTN and VSS is initially off, with inrush current limited to 140 mA while the bulk capacitor on VDD charges. After the inrush period, the MOSFET turns on fully, allowing operating current up to the current limit threshold (minimum 850 mA). The DEN pin can be pulled to VSS to disable the pass MOSFET, and the APD pin allows an auxiliary power source to take priority over PoE.

DC-DC Controller: The current-mode flyback controller operates from the PoE input voltage (typically 44-57V). The switching frequency is set by a resistor on the RT pin (referenced to ARTN). The controller uses peak current-mode control: the CS pin senses the primary-side MOSFET current through an external sense resistor, and the PWM comparator terminates the GATE on-time when the sensed current reaches the threshold set by the CTL voltage. The VB pin provides a 5V bias supply. The VC pin is the converter bias voltage bypassed with a minimum 0.47 uF capacitor to ARTN. The SRT pin sets the threshold for PWM-to-VFO transition, allowing the controller to enter variable frequency operation at light loads for higher efficiency.

Synchronous Rectification Control: The SRD output disables external synchronous rectifier MOSFETs during VFO mode to prevent reverse current flow. This enables seamless transition between continuous conduction mode (with sync rectification) and VFO mode (with diode rectification for light-load efficiency).

Adapter ORing: The APD input monitors an auxiliary power source. When APD is raised 1.5V above ARTN, the PoE pass MOSFET is disabled and T2P is forced active, enabling seamless switchover from PoE to adapter power without output interruption.

Pin Description: TPS23751PWPR Pin Definition and Functions
Pin Name Type Description
1 VDD Input Positive PoE input power rail; connect to PoE input after rectifier diode bridge; bypass with 0.1 uF to VSS
2 DEN I/O Detection enable; connect 24.9 kohm to VDD for PoE detection signature; pull to VSS to disable the pass MOSFET
3 CLS I/O Classification programming; connect resistor from CLS to VSS to set IEEE 802.3at classification current
4 APD Input Auxiliary Power Detect; raise 1.5V above ARTN to disable PoE pass MOSFET and force T2P active for adapter ORing
5 RT Input Switching frequency programming; connect resistor from RT to ARTN to set flyback switching frequency
6 T2P Output Type 2 PSE indicator; active low indicates type-2 PSE connected or APD active
7 SRD Output Synchronous Rectifier Disable; disables external synchronous rectifiers during VFO mode
8 CTL Input Control loop input to PWM comparator; connects to optocoupler output or feedback network
9 SRT Input Sets the threshold for PWM-to-VFO transition
10 VB Output 5V bias supply output; bypass with minimum 0.1 uF to ARTN
11 CS I/O Current sense input; connect to ARTN-referenced current sense resistor in MOSFET source
12 VC I/O DC-DC converter bias voltage; bypass with minimum 0.47 uF to ARTN directly at pin
13 GATE Output Gate driver output for external N-channel switching MOSFET
14 ARTN Power DC-DC converter analog return; connect to RTN; reference for CS, RT, VB, VC, SRT, CTL
15 RTN Power Drain of internal 0.5-ohm PoE pass MOSFET; connects to negative rail of PoE input
16 VSS Power Negative power rail from PoE source; system ground; PowerPAD must connect to VSS
Pad PowerPAD Power Exposed thermal pad; must connect to VSS for thermal dissipation
Application Scenarios: In which products and applications is TPS23751PWPR used
Application Description
VoIP Phones PoE-powered VoIP phones with 802.3at Type 2 support up to 25.5W; APD enables seamless wall adapter switchover
IP Security Cameras PoE-powered PTZ and dome cameras; flyback provides isolated 12V/5V output; VFO mode reduces thermal dissipation
Wireless Access Points 802.3at-compliant WiFi access points; sync rectification achieves high efficiency; programmable frequency optimizes EMI
Industrial PoE Devices PoE-powered industrial sensors and IoT gateways; wide 9.2V-57V input handles long cable drops; thermal shutdown protects in harsh environments
Pico/Femto Base Stations Low-power cellular base stations; adapter ORing enables dual-power operation; 25.5W supports multi-band radio
Alternative Models: What chips are recommended as replacements for TPS23751PWPR
Model Manufacturer Compatibility Key Difference
TPS23752PWP TI Superset 20-pin TSSOP with Sleep Mode; extends TPS23751 with WAKE, SLPb, MODE, LED pins
TPS23754PWP TI Functionally Similar High-efficiency PoE interface and DC/DC controller; different architecture; check pinout
TPS23756PWP TI Functionally Similar Flyback/forward DC-DC with 12V-57V adapter support; broader topology support
LTC4267 Analog Devices Functionally Similar PoE PD interface with switching regulator; 802.3af only (13W); no 802.3at Type 2
NCP1082 onsemi Functionally Similar 802.3at PoE PD controller with flyback; 25.5W; different pinout and programming

Recommend Parts

ISL95855HRTZ-T

IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN

Brand: Renesas

Package: 48-TQFN (6×6 mm, exposed pad)

IN STOCK: 2156pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4019PBF

150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 2409pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSP430F247TPMR

TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64

Package: See datasheet

IN STOCK: 13371pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1