Opens in a new tab

Home » Integrated Circuits ICs, Interface ICs » CP2102N-A02-GQFN20R

CP2102N-A02-GQFN20R

USB-to-UART bridge, USB 2.0 FS, 3Mbaud, 4 GPIO, integrated clock, QFN20 3x3mm T/R

53085

Effective Inventory

Image for reference only

Manufacturer Part:

CP2102N-A02-GQFN20R

Package:

QFN-20 (3.0 x 3.0 x 0.73 mm, 0.5mm pitch, exposed pad)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

The CP2102N-A02-GQFN20R from Silicon Labs is a USB-to-UART bridge controller in a 20-pin QFN (3x3mm) package with tape-and-reel packaging. It features USB 2.0 full-speed (12 Mbps) operation, data rates up to 3 Mbaud, integrated USB transceiver and clock (no external crystal required), 4 GPIOs, 512-byte TX and RX buffers, USB battery charger detection, remote wakeup, I2C interface, and royalty-free VCP drivers. Single 3.0-3.6V supply (5.25V tolerant via internal regulator). 9.5 mA typical operating current. Operating temperature -40C to +85C.

Product Introduction: CP2102N-A02-GQFN20R Product Introduction

The CP2102N-A02-GQFN20R from Silicon Labs is a highly integrated USB-to-UART bridge controller in a compact 3 x 3 mm QFN-20 package with tape-and-reel packaging (1500 units/reel). It is part of the USBXpress family, designed to quickly add USB connectivity to any UART-based design without firmware development.

The CP2102N integrates a USB 2.0 full-speed function controller, USB transceiver, oscillator, and UART in a single chip. No external USB components are required: no crystal (integrated 48 MHz oscillator), no pull-up resistors (integrated USB transceiver), and no EEPROM (960-byte internal configuration ROM). This minimizes BOM count and PCB area.

The A02 firmware revision supports USB battery charger detection (BCS 1.2), 4 GPIO pins, and I2C interface for advanced configurations. The QFN20 package variant provides 4 GPIO pins but does not have separate VIO and VDD pins (unlike the QFN24 variant). GPIO functions include LED indicators (TX/RX activity), clock output, and general-purpose I/O.

The UART supports all standard handshaking and modem interface signals (CTS, RTS, DSR, DTR, DCD, RI) for full RS-232 compatibility. Data formats include 5/6/7/8 data bits, 1/1.5/2 stop bits, and odd/even/mark/space/no parity. Baud rates range from 300 baud to 3 Mbaud with fractional baud rate generation for non-standard rates.

The 512-byte transmit buffer and 512-byte receive buffer prevent data loss during USB latency spikes. Hardware (RTS/CTS) or software (Xon/Xoff) flow control is supported.

The 960-byte internal configuration ROM stores vendor ID, product ID, serial number, power descriptor, release number, and product description strings. All customization is performed through the Silicon Labs Xpress Configurator GUI, requiring no firmware development.

Virtual COM port (VCP) drivers are royalty-free for Windows, Mac, and Linux. The drivers create a standard COM port that existing serial applications can use without modification. Custom USB device drivers are also supported through the Silicon Labs Direct Driver.

The device operates from a single 3.0-3.6V supply, with an internal voltage regulator that can also accept 3.0-5.25V supply for the USB transceiver. Typical operating current is 9.5 mA at 3.3V. The CP2102N is pin-compatible with the earlier CP2104 in the QFN24 package variant.

Working Principle: CP2102N-A02-GQFN20R Working Principle

**USB-to-UART Bridge:** The CP2102N translates between USB protocol and UART serial protocol. When data arrives from the USB host, the USB function controller parses the USB packets, strips the USB protocol overhead, and places the data into the TX buffer. The UART transmitter then serializes the data according to the configured baud rate, data format, and flow control settings, sending it out on the TX pin.

Conversely, data received on the RX pin is captured by the UART receiver, deserialized, and placed into the RX buffer. When the USB host polls the device, the USB function controller packages the RX buffer data into USB packets and sends it to the host.

**Integrated Oscillator:** The internal 48 MHz oscillator eliminates the need for an external crystal, saving BOM cost and board space. The oscillator has sufficient accuracy for USB full-speed operation (fractional frequency tolerance within USB specification).

**Configuration ROM:** The 960-byte internal ROM stores device descriptors that identify the USB device to the host. These include Vendor ID (VID), Product ID (PID), serial number string, and power descriptors. Silicon Labs provides a default VID/PID, or customers can purchase a unique VID/PID for custom applications. The Xpress Configurator GUI writes these settings to the ROM via the USB interface.

**USB Battery Charger Detection:** The BCS 1.2 charger detection circuitry identifies the type of USB charger connected (standard downstream port, charging downstream port, or dedicated charging port) and signals the result to the system via GPIO or I2C. This allows portable devices to draw higher charging current when connected to a wall charger.

Pin Description: CP2102N-A02-GQFN20R Pin Definition and Functions
Pin Name Type Description
1 VDD P Supply voltage; 3.0-3.6V (3.0-5.25V with internal regulator); decouple with 0.1uF + 4.7uF; powers internal logic and I/O
2 D+ I/O USB D+ data line; connect directly to USB connector D+ pin; no external pull-up required (integrated)
3 D- I/O USB D- data line; connect directly to USB connector D- pin; no external pull-up required
4 GND G Ground; connect to PCB ground plane; USB shield ground
5 TXD O UART transmit data output; connects to system MCU RXD; idle HIGH; 3.3V logic levels; 3 Mbaud max
6 RXD I UART receive data input; connects to system MCU TXD; idle HIGH; 3.3V logic levels; 5V tolerant
7 CTS I Clear To Send (active-low); UART hardware flow control input; connect to MCU RTS; leave unconnected if not used
8 RTS O Request To Send (active-low); UART hardware flow control output; connect to MCU CTS; active when CP2102N can accept data
9-12 GPIO0-3 I/O 4 general-purpose I/O pins; configurable via Xpress Configurator as LED indicators, clock output, or GPIO; shared with alternate functions; 3.3V logic
13 SUSPEND O USB suspend indicator; HIGH when USB bus is suspended; can be used to gate system power or enter low-power mode
14-20 GND/VDD/NC P/G/NC Additional ground, supply, and no-connect pins; follow datasheet pinout exactly
Application Scenarios: In which products and applications is CP2102N-A02-GQFN20R used
Application Description
USB Debug/Programming Port Add USB connectivity to MCU-based boards for programming and debug; UART TX/RX connect to MCU UART; GPIO0/1 configured as TX/RX LED indicators; VCP driver creates COM port; no firmware development on CP2102N side
USB Data Acquisition Dongle USB interface for sensor data acquisition; 3 Mbaud supports high-speed data streaming; CTS/RTS flow control prevents buffer overflow; 512-byte RX/TX buffers handle USB latency; QFN20 minimizes dongle size
Battery-Powered IoT Device USB charging and data transfer for IoT devices; BCS 1.2 charger detection enables fast charging from wall adapters; SUSPEND pin gates system power when USB disconnected; 9.5mA operating current minimizes power budget
Alternative Models: What chips are recommended as replacements for CP2102N-A02-GQFN20R
Model Manufacturer Compatibility Key Difference
CP2102N-A02-GQFN24 Silicon Labs More GPIO Variant Same function in QFN24 (4x4mm); 4 GPIO; separate VIO and VDD pins; supports mixed-voltage systems; larger footprint; pin-compatible with CP2104
CP2102N-A02-GQFN28 Silicon Labs Full-Featured Variant 7 GPIO; battery charger detect; QFN28 (5x5mm); pin-compatible with CP2101/2/9; use for designs needing all features
CH340G WCH Lower Cost Alternative USB-to-UART bridge; 2 Mbaud; requires external crystal; SOIC-16; much lower cost; Chinese-sourced; less driver support on newer OS; use for cost-sensitive consumer products

Recommend Parts

ISL95855HRTZ-T

IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN

Brand: Renesas

Package: 48-TQFN (6×6 mm, exposed pad)

IN STOCK: 2156pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4019PBF

150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 2409pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSP430F247TPMR

TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64

Package: See datasheet

IN STOCK: 13371pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NUC029LAN

ARM Cortex-M0 MCU, 50MHz, 64KB Flash, 4KB SRAM, dual UART/SPI/I2C, LQFP-48

Brand: Nuvoton

Package: LQFP-48 (7.0 x 7.0 x 1.45 mm)

IN STOCK: 12385pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1