The LM1117MPX-ADJ from Texas Instruments is an 800 mA low-dropout linear regulator in a SOT-223-4 package. The adjustable version sets output voltage from 1.25 V to 13.8 V using two external resistors. Key specifications include 1.2 V typical dropout at 800 mA, 1.262 V reference voltage with ±1% accuracy, 5 mA typical ground current, 0.035% typical line regulation, 0.2% typical load regulation, and 38 µVrms output noise. The device includes current limiting and thermal shutdown protection. Operating temperature range is 0°C to +125°C. The MPX suffix denotes SOT-223 tape-and-reel packaging (2000 units/reel).
Home » Integrated Circuits ICs, Low Dropout Regulators (LDO) » LM1117MPX-ADJ
LM1117MPX-ADJ
800mA LDO, 1.25-13.8V adj, 1.2V dropout@800mA, ±1% Vref, SOT-223 T&R, 0~125°C
Effective Inventory
Manufacturer Part:
LM1117MPX-ADJ
Package:
SOT-223-4 / DCY (6.5 x 3.5 x 1.6 mm, tab = VOUT pins 2&4)
Brand:
Product Categories:
Quality Commitment
Shipping & Payment
Service & Packaging
Product Manual
Other recommendations you may be interested in.
Description
Product Introduction: LM1117MPX-ADJ Product Introduction
The LM1117MPX-ADJ is the adjustable-output version of TI’s LM1117 low-dropout linear regulator in a SOT-223-4 surface-mount package with tape-and-reel packaging. The LM1117 is one of the most widely used LDO regulator families in the electronics industry, originally developed by National Semiconductor (now TI).
The adjustable version uses an internal 1.262 V bandgap reference trimmed to ±1% accuracy. The output voltage is set by two external resistors: VOUT = VREF × (1 + R1/R2) + IADJ × R1, where IADJ is typically 50 µA and can usually be neglected. This allows any output voltage from 1.25 V to 13.8 V with a single BOM change.
The 1.2 V typical dropout voltage at 800 mA (1.3 V max) means the input must be at least 1.3 V above the desired output for proper regulation. At lower currents, dropout scales proportionally: approximately 1.1 V at 100 mA and 1.25 V at 500 mA.
The SOT-223-4 package features a large tab (pins 2 and 4) connected to VOUT that serves as both the output connection and the primary thermal path. With RθJA of approximately 136°C/W on a standard FR4 board, the package can dissipate about 0.9 W at 50°C ambient.
TI also offers the LM1117I variant with -40°C to +125°C extended temperature range. For new designs, TI recommends the TLV1117 as a drop-in replacement with improved performance, or the TLV761 for fixed-voltage SOT-223 configurations with enhanced functionality.
Note: The LM1117MPX-ADJ (without /NOPB suffix) is listed as obsolete by some distributors. The LM1117MPX-ADJ/NOPB with Pb-free terminal finish remains active. Designers should specify the /NOPB variant.
Working Principle: LM1117MPX-ADJ Working Principle
**Bandgap Reference and Error Amplifier:** The LM1117 uses a Zener-trimmed bandgap reference that produces a stable 1.262 V reference voltage. This reference is compared against a fraction of the output voltage (fed back through the ADJ pin) by a high-gain error amplifier. The amplifier drives the series pass transistor to maintain regulation.
**Pass Transistor and Dropout:** The pass element is a PNP-driven NPN Darlington configuration. The minimum input-output differential (dropout voltage) is the saturation voltage of this Darlington, approximately 1.2 V at full load. Unlike CMOS LDOs where dropout equals IOUT × RDS(on), the bipolar Darlington has a relatively fixed saturation voltage that increases modestly with current.
**ADJ Pin and Resistor Divider:** In the adjustable configuration, the ADJ pin connects to the junction of two external resistors. The internal error amplifier drives the pass transistor to maintain VADJ = VREF (1.262 V). The ADJ pin sources a small bias current (IADJ ≈ 50 µA) that flows through R1, adding a small error term: VOUT = VREF × (1 + R1/R2) + IADJ × R1.
**Protection Circuits:** Current limiting restricts output current to approximately 1.2 A under fault conditions. Thermal shutdown disables the output when junction temperature exceeds approximately 165°C, with hysteresis to prevent oscillation.
Pin Description: LM1117MPX-ADJ Pin Definition and Functions
| Pin | Name | Type | Description |
|---|---|---|---|
| 1 | GND/ADJ | I | Adjust pin; connect to resistor divider junction; sets output voltage; VADJ = VREF = 1.262V; IADJ ≈ 50µA flows out; bypass with 10µF for improved ripple rejection |
| 2 | VOUT (tab) | O | Regulated output; tab connects to pins 2 and 4; connect both to output rail; minimum 10µF tantalum or 22µF ceramic required for stability; 800mA max |
| 3 | VIN | P | Input supply; 2.6V to 15V; must be ≥ VOUT + VDO; bypass with 10µF ceramic to GND |
| 4 | VOUT | O | Output (parallel with pin 2/tab); must connect to pin 2 on PCB; solder tab to copper pour with thermal vias for heat dissipation |
Application Scenarios: In which products and applications is LM1117MPX-ADJ used
| Application | Description |
|---|---|
| Adjustable Post-Regulator | Post-regulate switching pre-regulator output to reduce noise; adjustable 1.25-13.8V output via resistor divider; 1.2V dropout allows 5V→3.3V, 3.3V→1.8V; 47dB PSRR at 120Hz rejects switcher ripple |
| Battery-Powered Device Power | Regulate Li-ion battery (3.0-4.2V) to 2.5V or 3.3V rail; 800mA output; 5mA IQ acceptable for always-on circuits; thermal shutdown protects during overcurrent |
Alternative Models: What chips are recommended as replacements for LM1117MPX-ADJ
| Model | Manufacturer | Compatibility | Key Difference |
|---|---|---|---|
| TLV1117CDCYR | TI | Recommended Upgrade | Drop-in replacement; lower IQ (5mA vs 10mA); same SOT-223 pinout; use for new designs |
| LM1117MP-ADJ/NOPB | TI | Same Part (Pb-Free) | Identical function; Pb-free terminals; active status; specify this variant for new orders |
| AMS1117-ADJ | Advanced Monolithic Systems | Pin-Compatible Clone | Industry clone; same SOT-223 pinout; 800mA; slightly different dropout specs; widely available from multiple sources |
| AP2112K-ADJ | Diodes Inc | Functional Alternative | 600mA LDO; adjustable; SOT-23-5; much smaller package; lower current; use for space-constrained low-current applications |
Recommend Parts

ISL95855HRTZ-T
IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN
Brand: Renesas
Package: 48-TQFN (6×6 mm, exposed pad)
IN STOCK: 2156pcs
Cargo cycle: 3-7 Days
The minimum order is 1

IRFB4019PBF
150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB
Brand: infineon
Package: TO-220AB
IN STOCK: 2409pcs
Cargo cycle: 3-7 Days
The minimum order is 1

MSP430F247TPMR
TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64
Brand: texas-instruments
Package: See datasheet
IN STOCK: 13371pcs
Cargo cycle: 3-7 Days
The minimum order is 1

MMUN2211LT1G
NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch
Brand: Onsemi
Package: SOT-23-3 (TO-236, SC-59)
IN STOCK: 8500pcs
Cargo cycle: 3-7 Days
The minimum order is 1

PIC32MX795F512L-80I/PF
32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial
Brand: MICROCHIP
Package: TQFP-100 (14 x 14 mm)
IN STOCK: 7912pcs
Cargo cycle: 3-7 Days
The minimum order is 1








