The LM358P from Texas Instruments is a dual general-purpose operational amplifier in an 8-pin PDIP (through-hole) package. It contains two independent high-gain internally compensated op-amps designed for single-supply operation from 3 V to 30 V (or ±1.5 V to ±15 V). Key specs include 1.1-MHz gain bandwidth product, 0.5-V/µs slew rate, 2-mV typical input offset voltage, 45-nA input bias current, and 100-dB voltage gain. The input common-mode range includes ground, and the output swings from near 0 V to VCC-1.5 V. Quiescent current is 500 µA per amplifier. Output current capability is 40 mA typical at VCC=15V. Operating temperature range is 0°C to +70°C. The ‘P’ suffix denotes the plastic DIP-8 through-hole package.
Home » Analog Linear ICs, Integrated Circuits ICs » LM358P
LM358P
Dual op-amp, 3-30V single supply, 1.1MHz GBW, 2mV Vos, ground-sensing input, PDIP-8, 0~70°C
Effective Inventory
Manufacturer Part:
LM358P
Package:
PDIP-8 (P) (9.81 x 6.35 x 4.57 mm, 2.54mm pitch, through-hole)
Brand:
Product Categories:
Quality Commitment
Shipping & Payment
Service & Packaging
Product Manual
Other recommendations you may be interested in.
Description
Product Introduction: LM358P Product Introduction
The LM358P from Texas Instruments is the through-hole PDIP-8 version of the LM358, one of the most widely used dual operational amplifiers in the electronics industry. First introduced in the 1970s, the LM358 family remains in high-volume production due to its simplicity, low cost, wide availability, and single-supply capability. The ‘P’ suffix specifically denotes the plastic DIP-8 package for through-hole mounting, favored in prototyping, education, and industrial applications requiring manual soldering or socket installation.
The LM358 contains two independent op-amps sharing common VCC and GND pins. Each amplifier features internal dominant-pole compensation for unity-gain stability, eliminating the need for external compensation components. The input common-mode voltage range includes ground (0 V), which is the defining feature that distinguishes the LM358 from older dual-supply op-amps like the LM741. This allows the LM358 to directly amplify signals near ground without a negative supply rail.
The output swings from approximately 5 mV above ground (no load) to VCC – 1.5 V. The output can source 40 mA and sink approximately 20 mA at VCC = 15 V, sufficient for driving LEDs, small relays, and logic-level signals. The 500-µA per-amplifier quiescent current is modest for bipolar op-amps and is essentially independent of supply voltage.
The LM358P is electrically identical to the LM358N (ON Semiconductor’s PDIP-8 version) and LM358PT (ST’s PDIP-8 version). These parts are fully interchangeable in most applications. TI also offers the LM358B (3-36 V, 3-mV Vos, EMI filtering, 1.2-MHz GBW) as a drop-in upgrade for new designs.
The LM358 is the dual-channel companion to the LM324 quad op-amp. The two devices share identical amplifier cells and specifications, differing only in channel count and package. Designers needing only two amplifiers should use the LM358 to save board space; those needing four should use the LM324.
Working Principle: LM358P Working Principle
**Bipolar Input Stage:** Each LM358 amplifier uses a PNP differential pair (Q1-Q4 in the TI schematic) with a current-mirror load. The PNP inputs allow the common-mode range to include ground and extend -0.3 V below it. The 45-nA typical input bias current is the PNP base current flowing out of the input pins. The bias current creates a voltage error across source resistances; matching the DC resistance seen by both inputs minimizes this error.
**Internal Compensation:** A 30-pF internal capacitor provides dominant-pole compensation, setting the unity-gain crossover frequency to approximately 1.1 MHz and the slew rate to 0.5 V/µs. The compensation ensures stability with 100% feedback (unity-gain voltage follower) without external components. The relatively low slew rate limits full-power bandwidth to approximately 10 kHz for large signals.
**Class-AB Output with Current Sink:** The output stage can source 40 mA (via a Darlington pull-up) and sink 20 mA (via a current-sink transistor). The asymmetric drive capability means the output cannot truly swing to ground under load — it typically sits at 5-20 mV with no pull-down resistor, and rises to hundreds of millivolts when sinking more than a few µA. A pull-down resistor (10-100 kΩ) from output to ground helps the output reach near-zero volts in DC applications.
**Single-Supply Design:** The VCC- pin (pin 4) serves as both the ground reference and the return path for the output sink current. No negative supply is required, though split-supply operation (±1.5 V to ±15 V) is also supported by connecting VCC- to the negative rail.
Pin Description: LM358P Pin Definition and Functions
| Pin | Name | Type | Description |
|---|---|---|---|
| 1 | 1OUT | O | Amplifier 1 output; swings ~5mV to VCC-1.5V; 40mA source, 20mA sink capability |
| 2 | 1IN- | I | Amplifier 1 inverting input; 45nA bias current flows out of pin; differential input range up to VCC |
| 3 | 1IN+ | I | Amplifier 1 non-inverting input; common-mode range includes ground (0V to VCC-1.5V) |
| 4 | GND/VCC- | G | Ground / negative supply; connect to ground for single-supply; connect to -V for split-supply operation |
| 5 | 2IN+ | I | Amplifier 2 non-inverting input; same characteristics as 1IN+ |
| 6 | 2IN- | I | Amplifier 2 inverting input; same characteristics as 1IN- |
| 7 | 2OUT | O | Amplifier 2 output; same characteristics as 1OUT |
| 8 | VCC+ | P | Positive supply; 3V to 30V; bypass with 0.1µF ceramic to GND; supply current 500µA per amplifier typical |
Application Scenarios: In which products and applications is LM358P used
| Application | Description |
|---|---|
| Voltage Comparator / Window Detector | Use as open-loop comparator for overvoltage/undervoltage detection; ground-sensing input eliminates need for negative supply; two channels form window comparator with hysteresis; 40mA output drives relay or LED; add positive feedback for clean switching |
| Sensor Signal Conditioning | Amplify low-level signals from temperature sensors (NTC/PTC), photodiodes, or current-sense resistors; single 5V supply; ground-referenced input simplifies design; non-inverting gain of 10-100x for millivolt-level signals; RC low-pass filter on output for noise reduction |
| Current Sense Amplifier | Differential amplifier across current-sense resistor; ground-sensing input reads low-side shunt voltage; gain set by external resistors; single-supply operation from 5V or 12V rail; output feeds ADC input of MCU |
Alternative Models: What chips are recommended as replacements for LM358P
| Model | Manufacturer | Compatibility | Key Difference |
|---|---|---|---|
| LM358BPE4 | TI | Pin-Compatible Upgrade | 3-36V supply; 3mV max Vos; 50nA max Ib; integrated EMI filter; 1.2MHz GBW; drop-in upgrade with improved specs; use for new designs |
| LM358PT | ST | Pin-Compatible Equivalent | Same PDIP-8 package; electrically equivalent; ST variant; use as alternate source for supply chain flexibility |
| MCP6002-I/P | Microchip | Functional Alternative | Dual CMOS op-amp; 1.8-6V; 1MHz GBW; rail-to-rail I/O; 1pA Ib; PDIP-8; use for low-voltage rail-to-rail applications below 6V |
| LMV358IP | TI | Functional Alternative (Low-Voltage) | Dual op-amp; 2.5-5.5V; 1MHz GBW; rail-to-rail output; PDIP-8; use for 3.3V-only systems requiring output swing to rail |
Recommend Parts

ISL95855HRTZ-T
IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN
Brand: Renesas
Package: 48-TQFN (6×6 mm, exposed pad)
IN STOCK: 2156pcs
Cargo cycle: 3-7 Days
The minimum order is 1

IRFB4019PBF
150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB
Brand: infineon
Package: TO-220AB
IN STOCK: 2409pcs
Cargo cycle: 3-7 Days
The minimum order is 1

MSP430F247TPMR
TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64
Brand: texas-instruments
Package: See datasheet
IN STOCK: 13371pcs
Cargo cycle: 3-7 Days
The minimum order is 1

UCC28740DR
CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7
Brand: TI
Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)
IN STOCK: 4840pcs
Cargo cycle: 3-7 Days
The minimum order is 1

MMUN2211LT1G
NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch
Brand: Onsemi
Package: SOT-23-3 (TO-236, SC-59)
IN STOCK: 8500pcs
Cargo cycle: 3-7 Days
The minimum order is 1

PIC32MX795F512L-80I/PF
32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial
Brand: MICROCHIP
Package: TQFP-100 (14 x 14 mm)
IN STOCK: 7912pcs
Cargo cycle: 3-7 Days
The minimum order is 1







