Opens in a new tab

NC7SB3157P6X

SPDT analog switch/mux, 1.65-5.5V, 3-7Ohm Ron, 250MHz BW, break-before-make, SC-70-6, T&R

7617

Effective Inventory

Image for reference only

Manufacturer Part:

NC7SB3157P6X

Package:

SC-70-6 / SC-88 / SOT-363 (2.0 x 1.25 x 0.95 mm, 0.65mm pitch)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

The NC7SB3157P6X from onsemi (formerly Fairchild) is a low-voltage SPDT analog switch or 2:1 multiplexer/demultiplexer bus switch in a 6-pin SC-70 (SC-88/SOT-363) package. It operates from 1.65 V to 5.5 V with 3-7 Ohm typical on-resistance at 4.5 V, rail-to-rail signal handling, break-before-make switching, and 250 MHz -3 dB bandwidth. The select pin (S) chooses between B0 and B1 ports connected to the A port. Over-voltage tolerant control input to 7 V. Operating temperature range is -40C to +85C. P6X suffix denotes SC-70 tape-and-reel (3000 units/reel).

Product Introduction: NC7SB3157P6X Product Introduction

The NC7SB3157 from onsemi’s TinyLogic family (originally Fairchild, also sold as FSA3157) is a single-pole/double-throw (SPDT) analog switch that functions as a 2:1 multiplexer or 1:2 demultiplexer. The NC7SB3157P6X is the SC-70-6 tape-and-reel version with 3000 units per reel.

The device routes the common port A to either B0 or B1 based on the select (S) pin logic level. When S is LOW, A connects to B0; when S is HIGH, A connects to B1. The break-before-make circuitry ensures both switches are never simultaneously on during a select transition, preventing momentary short circuits between B0 and B1.

The 3 Ohm typical on-resistance at 4.5 V (7 Ohm max) introduces minimal voltage drop and signal distortion. Rail-to-rail signal handling allows the switch to pass analog signals from 0 V to VCC without clipping. The 250 MHz -3 dB bandwidth supports high-speed digital and video signal routing.

The device operates from 1.65 V to 5.5 V, covering all common logic voltages (1.8 V, 2.5 V, 3.3 V, 5 V). The control input tolerates voltages up to 7 V independently of VCC, enabling 5 V control signals in 3.3 V systems without level translation.

Power-down high-impedance on all I/O pins prevents backflow current when VCC is 0 V, supporting hot-swap and partial-power applications. The off-state leakage current is only 0.05 uA typical (1 uA max), ensuring minimal signal coupling in the off state.

Note: The NC7SB3157P6X-F40 variant (with -F40 suffix) has been marked obsolete by DigiKey. The base NC7SB3157P6X may still be available from other distributors. The FSA3157P6X is the same device from the Fairchild product line and may be used as a cross-reference.

Working Principle: NC7SB3157P6X Working Principle

**CMOS Transmission Gate Switch:** Each switch path (A-B0, A-B1) uses a CMOS transmission gate (parallel NMOS + PMOS). The NMOS passes signals near VCC well, while the PMOS passes signals near GND well. Together, they provide rail-to-rail signal handling with relatively flat on-resistance across the full voltage range.

**Break-Before-Make:** During a select pin transition, the currently-on switch opens before the new switch closes. This prevents a momentary low-impedance path between B0 and B1 that could cause current spikes or signal glitches. The break-before-make delay is built into the internal control logic.

**Select Logic:** The S pin controls which switch is on. S = LOW: A-B0 connected, A-B1 open. S = HIGH: A-B1 connected, A-B0 open. The select pin has CMOS input thresholds (0.7 VCC for VIH, 0.3 VCC for VIL at 2.3-5.5 V) and tolerates voltages up to 7 V regardless of VCC.

**Over-Voltage Tolerance:** When VCC is 0 V, all I/O pins enter a high-impedance state, preventing any current path between ports or into the supply. This enables hot-swap and live-insertion applications where cards may be plugged into powered systems.

Pin Description: NC7SB3157P6X Pin Definition and Functions
Pin Name Type Description
1 B1 I/O Switch port B1; bidirectional; connects to A when S=HIGH; high-Z when S=LOW; rail-to-rail signal (0 to VCC); 7Ohm max Ron@4.5V
2 A I/O Common port; bidirectional; connects to B0 or B1 depending on S; rail-to-rail signal; primary signal routing port
3 GND G Ground; connect to PCB ground plane; bypass VCC with 0.1uF to GND
4 B0 I/O Switch port B0; bidirectional; connects to A when S=LOW; high-Z when S=HIGH; rail-to-rail signal
5 S I Select input; LOW = A connected to B0; HIGH = A connected to B1; 7V over-voltage tolerant; CMOS input levels; must not float
6 VCC P Supply voltage; 1.65V to 5.5V; bypass with 0.1uF ceramic to GND; determines signal range (0 to VCC)
Application Scenarios: In which products and applications is NC7SB3157P6X used
Application Description
Audio Signal Routing Switch between two audio sources to one output; 3Ohm Ron@4.5V preserves audio quality; rail-to-rail handles full audio swing; break-before-make prevents pop/click noise during switching; 250MHz BW far exceeds audio needs
Battery/GPIO Voltage Selection Select between battery-backed and GPIO-driven signal paths; S pin from MCU; 1.65V min VCC for low-voltage systems; over-voltage tolerant select pin allows 5V control in 3.3V systems
2:1 Mux for ADC Input Route one of two sensor signals to single ADC input; low Ron minimizes signal attenuation; low charge injection (7pC) preserves ADC accuracy; break-before-make prevents sensor cross-coupling
Alternative Models: What chips are recommended as replacements for NC7SB3157P6X
Model Manufacturer Compatibility Key Difference
FSA3157P6X onsemi Identical (Fairchild Name) Same die, same package, same electrical specs; FSA prefix is Fairchild naming; NC7SB is TinyLogic naming; fully interchangeable
NC7SB3157L6X onsemi Package Variant Same function in MicroPak-6 (1.0mm wide leadless); smaller footprint; use when SC-70 is too large
SN74LVC1G3157DCKR TI Functional Equivalent SPDT analog switch; 1.65-5.5V; 10Ohm Ron@4.5V; SC-70-6; higher Ron; TI-sourced alternative
74LVC1G3157GW-7 Diodes Inc Competitive Alternative SPDT switch; 1.65-5.5V; 10Ohm Ron; SOT-363; Diodes Inc-sourced; lower cost option

Recommend Parts

ISL95855HRTZ-T

IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN

Brand: Renesas

Package: 48-TQFN (6×6 mm, exposed pad)

IN STOCK: 2156pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4019PBF

150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 2409pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSP430F247TPMR

TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64

Package: See datasheet

IN STOCK: 13371pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NUC029LAN

ARM Cortex-M0 MCU, 50MHz, 64KB Flash, 4KB SRAM, dual UART/SPI/I2C, LQFP-48

Brand: Nuvoton

Package: LQFP-48 (7.0 x 7.0 x 1.45 mm)

IN STOCK: 12385pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1