The TLV70433DBVR from Texas Instruments is a 24-V, 150-mA, fixed 3.3-V output, ultra-low-IQ low-dropout linear regulator in a 5-pin SOT-23 (DBV) package (2.9 x 1.6 mm). It operates with input voltage from 2.5 V to 24 V (30 V absolute max for new chip), with only 3.4-µA typical quiescent current stable across the full load range. Dropout voltage is typically 850 mV at 100 mA. The device features internal soft-start, overcurrent protection, and reverse polarity protection. PSRR is 60 dB at 100 kHz. Stable with output capacitor ≥ 0.47 µF. Operating junction temperature range is -40°C to +125°C.
Home » Integrated Circuits ICs, Low Dropout Regulators (LDO) » TLV70433DBVR
TLV70433DBVR
24V 150mA LDO, fixed 3.3V out, 3.4µA IQ, 850mV Vdo@100mA, SOT-23-5, -40~125°C, soft-start
Effective Inventory
Manufacturer Part:
TLV70433DBVR
Package:
SOT-23-5 (DBV) (2.9 x 1.6 x 1.15 mm, 0.95mm pitch)
Brand:
Product Categories:
Quality Commitment
Shipping & Payment
Service & Packaging
Product Manual
Other recommendations you may be interested in.
Description
Product Introduction: TLV70433DBVR Product Introduction
The TLV70433DBVR is the 3.3-V fixed-output variant of TI’s TLV704 family of ultra-low-quiescent-current LDO regulators. The device is designed for battery-powered and low-power MCU applications where extended battery life is paramount. The 3.4-µA typical quiescent current (4.5 µA max) is stable across the entire 0-150 mA output load range, meaning the regulator draws virtually no extra current at light loads.
The wide 2.5-V to 24-V input range (30 V absolute max for new chip) allows direct connection to unregulated supplies such as 12-V or 24-V industrial buses, unconditioned solar panels, or multi-cell battery packs without pre-regulation. This eliminates the need for a front-end buck converter in many low-power applications, reducing BOM count and cost.
The 850-mV typical dropout voltage at 100 mA reflects the high input-to-output differential that the device can tolerate. While not a low-dropout device in the traditional sense (compared to sub-200-mV LDOs), the TLV704 trades dropout performance for ultra-low IQ, which is the correct trade-off for always-on battery-powered systems where load current is modest.
Internal soft-start limits inrush current into the output capacitor during power-up, preventing voltage overshoot on the output rail. The overcurrent protection uses a brick-wall current limit scheme that clamps output current during faults. Reverse polarity protection prevents damage when input voltage is applied in reverse, a common failure mode in battery-powered systems.
The SOT-23-5 package (2.9 x 1.6 mm) occupies only 4.64 mm² of board area, making the TLV70433DBVR one of the smallest 24-V LDOs available. The MSL-1 rating allows unlimited floor life before soldering, simplifying manufacturing logistics. The device requires only a 0.47-µF minimum output capacitor (1 µF recommended), enabling compact layouts.
Working Principle: TLV70433DBVR Working Principle
**CMOS Pass Element:** The TLV704 uses a P-channel MOSFET pass element controlled by an error amplifier. The error amplifier compares a fraction of the output voltage (via an internal R1/R2 divider for fixed-output versions) with a 1.205-V bandgap reference. The PMOS gate is driven to maintain regulation. The high RDS(on) of the PMOS accounts for the relatively high dropout voltage but enables the ultra-low 3.4-µA ground current.
**Ultra-Low Quiescent Current:** The TLV704 achieves 3.4-µA IQ by using a micropower bandgap reference and a minimal bias current architecture. Unlike bipolar LDOs that require 0.5-5 mA of ground current, the CMOS design draws nearly constant IQ across the entire load range, because the error amplifier and reference consume the vast majority of the ground current.
**Internal Soft-Start:** During power-up, an internal current source charges the output capacitor gradually. This limits inrush current, reduces output voltage overshoot, and prevents stress on the input supply. The soft-start time is proportional to the output capacitor value.
**Overcurrent Protection:** A brick-wall current limit senses output current and clamps it to a fixed level (typically 300 mA). When the load exceeds this limit, the output voltage drops while the current remains clamped. The device enters thermal cycling if power dissipation causes overheating.
Pin Description: TLV70433DBVR Pin Definition and Functions
| Pin | Name | Type | Description |
|---|---|---|---|
| 1 | IN | P | Input supply; 2.5V to 24V (30V abs max for new chip); bypass with 0.1µF ceramic to GND |
| 2 | GND | G | Ground; connect to PCB ground plane |
| 3 | EN | I | Enable input; drive high (>1.2V) to enable; drive low (<0.4V) to disable; internal pull-up to IN if left floating |
| 4 | NC | – | No internal connection; leave floating |
| 5 | OUT | O | Fixed 3.3V output; bypass with ≥0.47µF ceramic capacitor (1µF recommended); max load 150mA |
Application Scenarios: In which products and applications is TLV70433DBVR used
| Application | Description |
|---|---|
| Smart Meter Power Supply | Regulate 12V/24V bus to 3.3V for MCU and radio; 3.4µA IQ minimizes battery drain in always-on metering; 24V input range accepts industrial bus voltage directly; pair with MSP430 or CC13xx low-power MCU |
| Building Automation Sensor | Power 3.3V wireless sensor node from 12V HVAC supply; ultra-low IQ extends battery backup life during power outages; SOT-23-5 fits inside small sensor enclosures; 0.47µF minimum Cout reduces BOM |
| Solar-Powered IoT Node | Regulate unconditioned solar panel (5-18V) to 3.3V for MCU; 3.4µA IQ wastes minimal harvested energy; 30V abs max handles open-circuit solar voltage; internal soft-start manages capacitor charging at sunrise |
Alternative Models: What chips are recommended as replacements for TLV70433DBVR
| Model | Manufacturer | Compatibility | Key Difference |
|---|---|---|---|
| TLV70418DBVR | TI | Series Variant | Same TLV704 family; fixed 1.8V output instead of 3.3V; pin-compatible SOT-23-5; use for 1.8V rails |
| TLV70450DBVR | TI | Series Variant | Same TLV704 family; fixed 5.0V output; pin-compatible; use for 5V rails from 12V/24V input |
| TLV70033DDCR | TI | Functional Alternative | 200mA LDO; 3.3V fixed; 2.7-5.5V input; 50µA IQ; lower dropout (175mV@200mA); SOT-23-5; use when VIN<5.5V and lower dropout needed |
| XC6206P332MR | Torex | Competitive Alternative | 3.3V 200mA LDO; 6V max input; 1µA IQ; SOT-23-3; smaller 3-pin package (no EN); use for lowest-cost always-on 3.3V rail under 6V |
Recommend Parts

ISL95855HRTZ-T
IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN
Brand: Renesas
Package: 48-TQFN (6×6 mm, exposed pad)
IN STOCK: 2156pcs
Cargo cycle: 3-7 Days
The minimum order is 1

IRFB4019PBF
150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB
Brand: infineon
Package: TO-220AB
IN STOCK: 2409pcs
Cargo cycle: 3-7 Days
The minimum order is 1

MSP430F247TPMR
TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64
Brand: texas-instruments
Package: See datasheet
IN STOCK: 13371pcs
Cargo cycle: 3-7 Days
The minimum order is 1

UCC28740DR
CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7
Brand: TI
Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)
IN STOCK: 4840pcs
Cargo cycle: 3-7 Days
The minimum order is 1

MMUN2211LT1G
NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch
Brand: Onsemi
Package: SOT-23-3 (TO-236, SC-59)
IN STOCK: 8500pcs
Cargo cycle: 3-7 Days
The minimum order is 1

PIC32MX795F512L-80I/PF
32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial
Brand: MICROCHIP
Package: TQFP-100 (14 x 14 mm)
IN STOCK: 7912pcs
Cargo cycle: 3-7 Days
The minimum order is 1







