Opens in a new tab

TPS61165DBVR

1.2A 38V LED boost driver, 3-18V in, 1.2MHz, EasyScale/PWM dimming, SOT-23-6

6506

Effective Inventory

Image for reference only

Manufacturer Part:

TPS61165DBVR

Package:

SOT-23-6 / DBV (2.9 x 2.8 x 1.45mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TPS61165DBVR from Texas Instruments is a high-brightness white LED boost driver in a SOT-23-6 package. With a 40V rated integrated switch FET and 1.2A switch current limit at 1.2MHz switching frequency, it drives up to 10 LEDs in series from 3V to 18V input, featuring EasyScale 1-wire digital dimming, PWM dimming, and integrated open-LED protection.

Key Specifications

Input Voltage Range 3V to 18V
Output Voltage Range Up to 38V
Internal Switch FET Rating 40V
Switch Current Limit 1.2A
Switching Frequency 1.2MHz fixed
LED Current per Channel Up to 400mA
Feedback Reference Voltage 200mV (2% accuracy)
Peak Efficiency Up to 90%
Dimming Methods EasyScale 1-wire digital / PWM
Open LED Protection 38V (integrated)
Quiescent Current 2.3mA typ. (switching)
Shutdown Current 1μA typ.
Package SOT-23-6 (2.9 x 2.8mm)
Operating Temperature -40°C to +85°C

Features

  • 40V rated integrated switch FET for driving up to 10 series LEDs
  • 1.2A switch current limit at 1.2MHz switching frequency
  • 3V to 18V input voltage range
  • 38V open-LED protection (output clamping)
  • 200mV feedback reference with 2% accuracy
  • EasyScale 1-wire digital interface for brightness control
  • PWM dimming via CTRL pin (5kHz to 100kHz)
  • Built-in soft start
  • Up to 90% efficiency
  • Load disconnect during shutdown
  • Non-burst dimming eliminates audible capacitor noise

Applications

  • White LED backlight for 7-10 inch LCD panels
  • General LED lighting and illumination
  • Portable projector LED drivers
  • Automotive interior LED lighting
  • Battery-powered LED flashlights
Product Introduction: TPS61165DBVR Product Introduction

The TPS61165DBVR from Texas Instruments is a high-brightness white LED boost driver featuring a 40V rated integrated switch FET with 1.2A current limit and 1.2MHz fixed switching frequency. Operating from 3V to 18V input, it drives up to 10 white LEDs in series with output voltages up to 38V. LED current is set by an external sense resistor with a 200mV feedback reference (2% accuracy). The CTRL pin provides dual dimming modes: EasyScale 1-wire digital interface for precise current control, or PWM dimming where duty cycle adjusts the reference voltage. The device does not burst the LED current in either mode, eliminating audible noise on output capacitors.

Working Principle: TPS61165DBVR Working Principle

The TPS61165 is a current-mode boost converter that regulates LED current through a sense resistor from the FB pin to GND. The internal N-channel MOSFET switches at 1.2MHz, storing energy in the external inductor during the on-time and delivering it to the LED string through an external Schottky diode during the off-time. The current-mode control scheme provides cycle-by-cycle current limiting and stable operation with slope compensation for duty cycles above 40%. The CTRL pin serves as a multifunction control: a constant high enables normal operation, a PWM signal adjusts brightness by modulating the FB reference voltage, and the EasyScale protocol provides 1-wire digital brightness control. Open-LED protection monitors the SW pin voltage and disables the converter if the output exceeds 38V.

Pin Description: TPS61165DBVR Pin Definition and Functions
Pin Name Type Function
1 VIN Power Input supply (3V to 18V)
2 CTRL Input Enable / PWM dimming / EasyScale interface
3 SW Power Switch node (inductor connection)
4 GND Power Ground
5 COMP Output Error amplifier output (compensation cap)
6 FB Input Current feedback (sense resistor to GND)
Application Scenarios: In which products and applications is TPS61165DBVR used
  • 7-10 inch LCD panel white LED backlight driver
  • High-brightness LED general illumination boost driver
  • Portable projector RGB LED current source
  • Automotive interior LED lighting from 12V battery
  • Battery-powered flashlight and torch LED drivers
Alternative Models: What chips are recommended as replacements for TPS61165DBVR
Manufacturer Part Number Package Notes
TI TPS61165DRVR WSON-6 2x2mm WSON with thermal pad
TI TPS61175PWPR TSSOP-14 3A switch, 24V, external dimming
onsemi CAT4139TD-T3 SOT-23-6 750mA LED boost driver
Monolithic Power MP3205DJ-LF-Z SOT-23-6 1.3A, 30V LED boost driver
Diodes Inc AL8805WS-7 SOT-25 1A LED buck driver alternative

Recommend Parts

ISL95855HRTZ-T

IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN

Brand: Renesas

Package: 48-TQFN (6×6 mm, exposed pad)

IN STOCK: 2156pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4019PBF

150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 2409pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSP430F247TPMR

TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64

Package: See datasheet

IN STOCK: 13371pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1