The TXS0102DCUR from Texas Instruments is a 2-bit bidirectional voltage-level translator for open-drain and push-pull applications in an 8-pin VSSOP (DCU) package. It supports A-port voltages from 1.65 V to 3.6 V (VCCA) and B-port voltages from 2.3 V to 5.5 V (VCCB), enabling translation between 1.8-V, 2.5-V, 3.3-V, and 5-V logic nodes without direction control. Maximum data rates are 24 Mbps (push-pull) and 2 Mbps (open-drain). Features include VCC isolation, partial-power-down Ioff support, no power-supply sequencing requirement, and ESD protection up to 8-kV HBM on the B port. Operating temperature range is -40°C to +85°C.
Home » Integrated Circuits ICs, Interface ICs » TXS0102DCUR
TXS0102DCUR
2-bit bi-dir level shifter, 1.65-3.6V A / 2.3-5.5V B, 24Mbps push-pull, auto-direction, VSSOP-8, -40~85°C
Effective Inventory
Manufacturer Part:
TXS0102DCUR
Package:
VSSOP-8 (DCU) (2.3 x 2.0 x 0.9 mm, 0.5mm pitch)
Brand:
Product Categories:
Quality Commitment
Shipping & Payment
Service & Packaging
Product Manual
Other recommendations you may be interested in.
Description
Product Introduction: TXS0102DCUR Product Introduction
The TXS0102DCUR is a 2-bit bidirectional voltage-level translator from Texas Instruments designed for mixed-voltage systems where I²C, UART, GPIO, or other digital signals must cross between different voltage domains. It requires no direction-control signal — each channel automatically senses and translates in both directions, simplifying board design.
The A port operates from 1.65 V to 3.6 V (tracking VCCA), and the B port operates from 2.3 V to 5.5 V (tracking VCCB), with the constraint VCCA ≤ VCCB. This covers all common logic voltage combinations: 1.8 V-to-3.3 V, 1.8 V-to-5 V, 3.3 V-to-5 V, and 2.5 V-to-3.3 V.
The TXS architecture uses passive pass-transistor switches with edge-rate accelerators. For open-drain buses (I²C, SMBus), the pass-FET provides a low-impedance path and the one-shot accelerator briefly turns on a strong pull-up to speed rising edges, achieving up to 2 Mbps. For push-pull signals (UART, SPI, GPIO), the accelerator provides fast edges up to 24 Mbps.
The VCC isolation feature ensures that if either VCCA or VCCB is at GND, both ports enter a high-impedance state, preventing back-feeding. The Ioff circuitry supports partial-power-down mode, allowing one side to be powered down while the other remains active without leakage. No power-supply sequencing is required — either rail can ramp first.
ESD protection is asymmetric: the A port provides 2.5-kV HBM, while the B port (facing the higher-voltage, often external-facing side) provides 8-kV HBM. The OE pin, when pulled low, places all I/Os in high-impedance state with reduced quiescent current. The VSSOP-8 (DCU) package occupies only 4.6 mm² of board area, making it ideal for space-constrained portable designs.
Working Principle: TXS0102DCUR Working Principle
**Pass-FET Switch Core:** Each channel consists of an N-channel pass transistor connecting the A and B sides. The pass-FET gate is biased at a voltage between VCCA and VCCB, allowing bidirectional current flow when either side drives low. The on-resistance is approximately 10 Ω, providing a low-impedance path for DC and low-frequency signals.
**Edge-Rate Accelerator:** One-shot circuits on each side detect falling edges and briefly turn on a strong pull-down (≈ 30 mA for ~30 ns) to accelerate the transition. For rising edges on open-drain buses, the accelerator briefly turns on a strong pull-up to overcome the weak external pull-up resistor. This enables 2 Mbps on I²C at 3.3-V/5-V translation.
**Auto-Direction Detection:** The TXS translator has no explicit direction control. The pass-FET inherently allows either side to drive the bus low. When neither side is driving, the external pull-up resistors (for open-drain) or the driving device (for push-pull) pull the line high through the pass-FET. This transparent operation eliminates the need for a DIR pin.
**VCC Isolation and Ioff:** When either supply is at GND, an internal circuit detects the condition and opens the pass-FET, placing both I/Os in high-impedance. The Ioff feature ensures that no leakage current flows from the powered side to the unpowered side, which is critical for hot-swap and battery-backup applications.
Pin Description: TXS0102DCUR Pin Definition and Functions
| Pin | Name | Type | Description |
|---|---|---|---|
| 1 | VCCA | P | A-port supply (1.65-3.6V); powers A-side I/O buffers and OE input logic; bypass with 0.1µF ceramic to GND |
| 2 | A1 | I/O | Channel 1 A-port I/O; voltage referenced to VCCA; connects to low-voltage side of signal |
| 3 | A2 | I/O | Channel 2 A-port I/O; voltage referenced to VCCA |
| 4 | GND | G | Ground; connect to PCB ground plane |
| 5 | B2 | I/O | Channel 2 B-port I/O; voltage referenced to VCCB; connects to high-voltage side of signal |
| 6 | B1 | I/O | Channel 1 B-port I/O; voltage referenced to VCCB |
| 7 | VCCB | P | B-port supply (2.3-5.5V); powers B-side I/O buffers; must be ≥ VCCA; bypass with 0.1µF ceramic to GND |
| 8 | OE | I | Output enable (active high); referenced to VCCA; tie to GND via pull-down resistor for safe power-up; internal pull-up to VCCA; pull low to disable all I/Os (Hi-Z) |
Application Scenarios: In which products and applications is TXS0102DCUR used
| Application | Description |
|---|---|
| I²C/SMBus Level Shifting | Bridge 1.8V or 3.3V MCU I²C bus to 5V peripheral; auto-direction handles bidirectional SDA without DIR pin; 2Mbps supports 1MHz Fast-mode Plus; pull-up resistors on both sides set idle-high levels |
| UART Cross-Voltage Communication | Translate 3.3V MCU UART TX/RX to 5V GPS module or cellular modem; push-pull mode supports 24Mbps; OE pin allows MCU to tri-state bus for shared UART lines |
| GPIO Voltage Adapter | Interface 1.8V SoC GPIOs to 3.3V or 5V sensors and displays; both channels independently handle mixed open-drain and push-pull signals; VCC isolation protects SoC when peripheral power is off |
Alternative Models: What chips are recommended as replacements for TXS0102DCUR
| Model | Manufacturer | Compatibility | Key Difference |
|---|---|---|---|
| TXS0102DCTT | TI | Pin-Compatible, Same Die | SSOP-8 package (2.95×2.80mm vs VSSOP 2.3×2.0mm); same electrical specs; use when SSOP footprint preferred |
| TXS0108EPW | TI | Functional Upgrade, 8-bit | 8-channel version; TSSOP-20; same VCCA/VCCB ranges; auto-direction; use when more channels needed in single package |
| PCA9306DCUR | TI | Functional Equivalent | 2-bit bidirectional; VSSOP-8; open-drain only (no push-pull); requires external pull-ups; use for I²C-only applications |
| SN74LVC1T45DBVR | TI | Competitive Alternative | 1-bit with DIR pin (direction control); SOT-23-6; 200Mbps; requires direction signal; use for high-speed unidirectional translation |
Recommend Parts

ISL95855HRTZ-T
IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN
Brand: Renesas
Package: 48-TQFN (6×6 mm, exposed pad)
IN STOCK: 2156pcs
Cargo cycle: 3-7 Days
The minimum order is 1

IRFB4019PBF
150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB
Brand: infineon
Package: TO-220AB
IN STOCK: 2409pcs
Cargo cycle: 3-7 Days
The minimum order is 1

MSP430F247TPMR
TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64
Brand: texas-instruments
Package: See datasheet
IN STOCK: 13371pcs
Cargo cycle: 3-7 Days
The minimum order is 1

UCC28740DR
CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7
Brand: TI
Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)
IN STOCK: 4840pcs
Cargo cycle: 3-7 Days
The minimum order is 1

MMUN2211LT1G
NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch
Brand: Onsemi
Package: SOT-23-3 (TO-236, SC-59)
IN STOCK: 8500pcs
Cargo cycle: 3-7 Days
The minimum order is 1

PIC32MX795F512L-80I/PF
32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial
Brand: MICROCHIP
Package: TQFP-100 (14 x 14 mm)
IN STOCK: 7912pcs
Cargo cycle: 3-7 Days
The minimum order is 1







